A walk-in tub door leak almost always traces back to one of a short list of causes, and the number one cause by far is leveling: if even one leveling leg is not carrying its share of the weight, the frame flexes, the door goes slightly out of alignment, and water finds the gap. Before anything else, check the legs, then work down the checklist below. Most door leaks are resolved at home without a service visit, and a whole new door is almost never the answer.
Start with the Leveling Legs
Chapters in this video
0:00Leveling Legs Are CriticalMany Ella's Bubbles walk-in tubs have up to eight leveling legs to evenly disperse weight and ensure proper function.
0:14Secure Each FootThe technician checks if each foot is securely on the ground, as an unsealed door could leak.
0:28Check Tub LevelsThe technician checks levels on all sides of the tub to ensure all feet sit securely on the floor.
0:41Proper Door AlignmentProper leveling assures correct door alignment and closure for your walk-in tub.
Many of Ella's walk-in tubs have as many as eight leveling legs to evenly disperse weight, and these adjustable legs are critical to the proper functioning of your tub. Check to see if each foot is securely on the ground. If not, the door will not seal correctly and could leak. Adjust each leg as necessary, check levels on all sides of the tub, and make sure all feet sit securely on the floor. This assures proper door alignment and proper closure. Our leveling guide covers the full procedure.
The Full Checklist, in Order
Legs and level. Every leg firmly on the floor, no gaps, weight shared equally, tub level on all sides. Extending or shortening legs is also how you close any visible gap between the door and its frame. Our article on doors that rub the frame walks through the adjustment in detail.
Clean the seal and frame. Debris or residue on the gasket or the door frame is a common leak cause. Wipe both down with a common household cleaner or rubbing alcohol.
Inspect the gasket. Look for a section that has pulled out of its channel or stayed compressed. A shipping-deformed seal can be restored by squeezing it with your fingertips and pulling it away from the frame; a loose seal can be re-secured with a thin bead of silicone, set 20 minutes, then a 24 hour cure. The door seal care article has the steps.
Let the seal reform. If the door has been kept latched, leave it open for about a day, or at least overnight, then fill and check again. Many leaks clear with this step alone.
Check the handle and latch. On outward-swing doors, make sure the handle rotates fully; the handle faces away from the hinges when unlocked and toward the hinges when locked. A handle that was refitted in the wrong orientation will result in improper door closure and potential leaks. On the stainless inward door, a handle that is not flush needs its lock nut snugged.
Confirm where the water is really coming from. Water behind or under the tub near the faucet end is often not the door at all: a hand shower that was wall-mounted without the barrel extension hose kit drips through the deck insert hole. That one is solved with the Leak Elimination Kit rather than any door work. Our guide to water under or behind the tub covers the other usual sources.
Inspect the full loop of the gasket and the frame it closes onto, not only the spot where the drip appears.
Seal Maintenance on Video
Chapters in this video
0:00Clean Your Door Seal RegularlyThe video explains how to clean the door seal and frame to prevent leaks and debris buildup.
0:38Replacing a Loose Door SealThe video demonstrates how to replace a loose or damaged door seal by applying a thin bead of silicone to the gasket channel.
1:02Adding Silicone to Inward DoorsThe video shows how to add a bead of silicone to the corner of the gasket where it meets the frame on inward swing doors.
1:23Extend Gasket LifeThe video recommends leaving the walk-in tub door slightly open when not in use to extend the gasket's flexibility and life.
This maintenance video applies to both inward and outward doors. It shows cleaning the seal and the door frame with a common household cleaner, explains why residue and debris cause leaks, demonstrates how to secure a loose gasket with a thin bead of silicone in the channel (set 20 minutes before reinserting, dry 24 hours), shows the extra bead where the gasket meets the frame on inward doors, and closes with the rule to leave the door slightly open when the tub is not in use. Watch: Ella's Bubbles: Proper Door Seal Maintenance-Inward and Outward Swing Doors with chapters and a full transcript.
Verify with a Standing Water Test
The same test used at installation works for you now: close the door, fill above the door threshold, and let the water stand while you watch the door line. The installer's warranty checklist requires the door seal to be watertight after a 20-minute fill, so that is the benchmark your tub was built to meet.
Never Lean on the Door
This deserves its own section because it is the easiest leak to prevent. Every Ella door, inward or outward, is designed to hold its own weight only, never the bather's weight. Leaning, sitting, or pressing on the door during entry, exit, or a wheelchair transfer can gradually shift the door's alignment, and alignment is exactly what keeps the seal watertight. It also matters for coverage: the warranty of the door and the door seal is valid only if the alignment of the bathtub and the door is done correctly, and the alignment of the door is not changed by applying the bather's weight on the door. Your tub gives you better places to hold: sturdy deck-mounted and wall-mounted grab bars are positioned for entry and exit, so let them take your weight every time. If a door has already been leaned on and now sits low, the hinge adjustment video guide shows the small correction.
Hold the grab bar, not the door. The door's alignment is what keeps the seal watertight.
If the Leak Persists
Some situations are ours to handle, and we are glad to. Open a ticket with your serial number, found on the label behind the magnetic access panel next to the door, plus photos of the leak area and a short description: where the water appears, whether it is the same spot every time, and whether the door is left open between baths. Photos of the affected part and a problem description are required for warranty part verification, and the shell, frame, door, and door seal are covered by our Lifetime Limited Warranty. Replacement seals, hinges, and hardware ship to you after verification, with hardware covered by the 5-year parts warranty.
Leveling. Confirm every leveling leg is touching the floor with equal weight, raising the center leg if the tub is bowed. Then clean and reseat the seal, leave the door ajar for a day, and check the handle orientation before anything else.
Is a leaking door covered under the warranty?
The door and door seal are Lifetime Limited Warranty parts, verified with photos. Leaks caused by misleveling or by a door whose alignment was changed by a bather's weight are excluded, which is why the leveling and grab bar habits matter.
Water sits in the door frame and drains down the latch hole. What does that mean?
Water pooling in the frame usually means the door is not compressing the seal evenly on that side. Check the legs, the handle position and the full gasket loop, then run the 20-minute fill test. If it continues, send the team a photo of exactly where the water collects.
The door on my LayDown leaks at the bottom.
If your Ella's Bubbles LayDown walk-in tub door leaks at the bottom, you should follow the same troubleshooting checklist as other models. This includes checking the tub's leveling, ensuring the door seal is clean and fully seated, and confirming no weight is applied to the glass door. The LayDown door seal is a unique part with its own installation video, which you can find in our LayDown door seal guide.
Does keeping the door closed cause leaks?
Yes, keeping the walk-in tub door closed and latched can cause leaks over time. A door kept latched continuously compresses the gasket, which can weaken its flexibility and lead to leaks. To extend the gasket's life and prevent leaks, leave the door slightly open when the tub is not in use, and after a leak, leave it open for about a day before refilling.
My installer tried silicone and the door still leaks.
Silicone belongs only as a thin bead inside the gasket channel to hold a loose seal, never over the seal line. Remove any silicone from the sealing face, clean the gasket and frame, re-check leveling and the handle, and then open a ticket with photos if it continues.
Is the water really coming from the door?
Water appearing under or behind your Ella's Bubbles walk-in tub is not always coming from the door. If the water is at the faucet end or under the tub, check for other common sources. These include a wall-mounted hand shower that was installed without the barrel extension hose kit, an over-tightened drain elbow, or a loose supply union. Our guide to Water Under or Behind the Tub covers these and other usual sources.
Do I need a whole new door?
You almost never need a whole new door to fix a leak on your Ella's Bubbles walk-in tub. The vast majority of door leaks are resolved by simpler solutions. These include cleaning and reseating the door seal, re-leveling the tub, or making an adjustment to the handle or latch. In some cases, replacing only the door seal is sufficient to stop the leak.
The door still leaks after a new seal. What does support look at next?
On an inward door with the hinge on the left, the handle points to about nine o'clock when locked and three o'clock when open, and the door should push closed freely without anyone touching the seal. The team checks for a bowed tub, since the walls should be straight across, a seal that is pinched or sitting high at one end, and correct handle installation. A video call lets them watch the door open and close before another seal is sent.
The latch bar does not tighten the door the way it used to. Is there a part for that?
Yes, if the latch bar on your Ella's Bubbles walk-in tub door no longer tightens the door as it should, there is a replaceable part for that. The plastic door wedge, which the latch bar engages to compress the door seal, can be replaced. To ensure you receive the correct version, provide a photo of the latch area and the model label found behind the magnetic access panel to the support team.
My mother cannot fit through the door, sit inside and close it. Is there a different door or handle?
There is one handle design and it cannot be relocated or doubled, so the remedy is a larger tub with a wider door and seat. The team can help match a model to her measurements. Ella door seals and parts are made for Ella tubs only and are not offered for other brands.
My door only leaks once the water climbs to a certain level. What does that mean?
Some doors stay dry at first and then begin to weep at the bottom once the water is about 6 inches deep or reaches the height of the handle. That pattern points to a seal that is not compressing evenly along the lower run rather than to a failed door. Check that every leveling leg carries weight, clean and fully reseat the gasket, confirm the handle turns all the way to the locked position, and then repeat the 20-minute fill test.
Will a replacement gasket by itself fix my leaking door?
Not always. A new gasket only seals well when the door is correctly adjusted to the frame, so a leak can continue after the swap if the leveling and door alignment were never corrected. Work through the leveling and hinge adjustment steps first, and if water still appears after the new seal is in, open a ticket with photos so the team can look at the door fit.
I found cracks on the inside of my walk-in door. What should I do?
Cracks can appear on the inside face of a walk-in door, and that is something the team wants to see rather than have you patch yourself. Open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your serial number from the label behind the magnetic access panel and clear photos of the cracked area. The door is a Lifetime Limited Warranty part, and photos plus a short description are what the team uses to verify coverage and send what is needed.
What is the Auto Purge function and why does water still drip after I stop the jets?
Auto Purge runs for a few minutes after you switch off the jets, blowing water out of the air lines to help prevent mold or bacteria buildup, so a little dripping right after the jets stop is expected. If the dripping continues steadily rather than only during that purge cycle, the cause is more likely a leak in the air lines themselves. In that case, open a ticket with photos so the team can take a closer look.
How can I find where a leak under the tub is coming from?
To find where a leak under the tub is coming from, remove the end panel at the drain end and look underneath while the tub has water in it. Some of the lines under the tub carry water as well as air, so a leak in one of these lines often becomes visible during the Auto Purge cycle. Take a close-up photo of exactly where the water is escaping before you open a ticket.
What should I do if a leak is reaching the wall or a closet near my tub?
If a leak is reaching a wall or a closet near your tub, stop filling the tub and shut off the water supply right away to limit further water damage. Once the water is off, open a ticket at ellasbubbles.com/support or call (800) 480-6850 with photos of the damage and the affected area. The team will use those photos to help determine the cause and next steps.
What information does the team need for a leak that has caused damage?
For a leak damage report, the team needs photos of the damage, close-up photos of the wet area under the tub showing exactly where the water is escaping, and your model and serial number from the label behind the magnetic access panel. They also ask for your installer's name and phone number as part of that report. Having this ready when you open a ticket helps the team process your report smoothly.
Why does the top of my walk-in tub door touch the frame while the bottom sits further out?
A door that looks warped this way can be caused by the middle leveling leg needing adjustment, even when the tub appears level. Raising the middle leveling leg can open up the door jamb, especially at the top, and correct a belly in the door. Make the change in small steps and confirm every leg still carries its share of the weight. If the door still sits unevenly, open a ticket at ellasbubbles.com/support or call (800) 480-6850 with photos.
Is the door gasket glued in, and what if it will not hold tight in the corners?
The door gasket is inserted into a channel around the frame, not glued. If the seal is not holding perfectly tight, especially in the corners or along the bottom, the gasket may not be fully inserted into its channel. Reseat the full loop of the gasket and then repeat the fill test to check the door line.
What can be done when a walk-in tub door leaks on the handle side?
Start by cleaning the door seal with rubbing alcohol and confirming that the leveling legs sit directly underneath and firmly against the floor. A small shim between the handle and the latch can add pressure as a temporary measure. For a lasting fix, the support team can provide a pre-cut shim that fits behind the latch part, which means the latch is removed and re-attached. Reach them at ellasbubbles.com/support or (800) 480-6850 with photos of the leak area.
How can I tell if my leveling legs are firmly on the floor?
Try to slide a sheet of printer paper underneath each leveling leg; it should not be possible. The access panels on either side of the tub can be removed so you can check the legs underneath the door. If a leg is not firmly against the floor, the frame can warp when the tub fills and let water past the door seal.
What should a healthy door seal look like?
A healthy seal is snug but not stuck together like a pancake. It should be slightly rounded, like an air tube, and open in the middle. It should also sit pressed down evenly within its edges, not high on one end or the other.
Why does my door need a push to close the seal?
A door that sits ajar or needs a push to close the seal can be a sign that the tub is slightly off balance. Check that every leveling leg is firmly on the floor and that the tub is level on all sides. If the door still will not close properly, contact us at ellasbubbles.com/support or (800) 480-6850.
Can support look at my door seal over a video call?
Yes, technical support can hold a video call to look at how your door closes and how the seal is sitting. To set that up, visit ellasbubbles.com/support or call (800) 480-6850.
How can I test my door for leaks at home?
Close the door, fill the tub above the door threshold, and let the water stand while you watch the door line. This is the same test used at installation. The installer's warranty checklist requires the door seal to be watertight after a 20-minute fill, so that is the benchmark your tub was built to meet.
Can a settling floor cause my walk-in tub door to start leaking?
Yes, it can. If the floor settles or the tub is no longer firmly against the floor, the frame can warp and create gaps in the door seal. Checking that every leveling leg sits securely on the floor and adjusting the legs as needed restores proper door alignment and closure.
Does a walk-in tub door seal have a set useful life?
Door seals are generally durable and do not have a published wear-out period. To help your seal keep its shape, leave the door slightly open when the tub is not in use, because keeping it closed can over-compress the seal and wear it down.
For anything specific to your model or serial number, open a ticket at ellasbubbles.com/support or call (800) 480-6850, and please attach photos so the team can help you quickly.
About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.