Switch the tub off at its dedicated breaker first. That stops the pumps, and it is the right move whenever the controls will not respond. Then work through three simple checks, because one normal behavior and two easy control mix-ups look exactly like this, and all of them are covered alongside the repair steps in Touchpad or push button controls not responding: checks, repair, and replacement.
Stop the Pumps at the Breaker, Then Drain
When a pump is running and the deck controls do nothing, there is no need to keep pressing. Go to the electrical panel and switch off the dedicated breaker for the tub. With the power off the pumps stop, and you can take your time with everything else on this page.
Do it in that order: power off first, drains second. A pump should never run on a dry tub, because a dry run causes permanent damage that is not covered. While the water still sits above the jets the pumps are protected, so there is no rush to pull the drains before the power is off. Once the breaker is off, open the drains and exit the tub normally after it empties.
If the bather is comfortable and you would rather watch the tub for a few minutes before cutting power, that is fine too, because two of the causes below end on their own.
Rule Out the Auto Purge, Which Looks Exactly Like This
On any tub with the air massage, the Auto Purge starts by itself about 20 minutes after the air pump is turned off and runs for 120 seconds to blow residual water out of the air lines. It is fully automatic and it cannot be stopped. The other features will not respond while it runs, and it is normal even if it starts while you are still sitting in a full tub.
So if the pattern was a blower that came on by itself, buttons that seemed dead, and then quiet again about two minutes later, nothing is wrong. Let it finish and try the buttons again. The video on this page shows the three-speed air massage being cycled with gentle presses and explains that the tub will sound like it is still running when it is only the Auto Purge doing its job. The timing that applies to your tub is the 20 minute figure given here.
Two more things a healthy tub does are worth knowing before you decide a pump is stuck on:
- The control box shuts the pumps off automatically after 20 minutes of continuous running, and starting the system again begins a new cycle. A pump that is still running well past that point, with no response from the controls, is not following the built-in timer.
- A light humming with nothing switched on is the ozone generator running by itself on a hydro massage tub. It is normal, and it is not a pump.
All of the built-in stops and restarts are sorted by what you see and hear in Why do my walk-in tub jet and blower motors stop and restart?
Push Button Tubs: A Button That Stays Down Is an Air Lock
Chrome push buttons are pneumatic. Pressing the button sends a puff of air down a small red tube, and that pressure activates the relay switch inside the control box that powers the pump or the light. If a button is stuck down and will not pop back up, air is trapped in that tube. That is an air lock, and the pump it controls cannot be switched off from the deck until it is released.
- With the breaker off, pull the large access panel off the front of the tub and find the blue control box.
- Pull the small red air tube off its fitting at the control box. The button on the deck should pop back up.
- Push the tube firmly back onto the box with a twist and push so it seats securely.
- Restore power and press the button gently. You should hear a click from the control box each time you press.
Before you decide a button is stuck, count your presses. On push controls the air massage is a counting control: the first press is high speed, the second is medium, the third is low, and a fourth press turns the system off. An air pump that seems to ignore the button may simply be on a different speed. Press gently as well. A push with the palm of the hand is enough, and pressing too hard or too deep can damage the mechanism.
Digital Touchpad: Hold for Two Seconds, Do Not Tap
On the digital panel the most common reason a pump will not shut off is the gesture. The air massage does not stop with a quick tap. Touch the air bubble icon to start it, use plus and minus for the speed, and hold the icon down for two seconds to turn it off. The chromatherapy light turns off the same way, with a two second hold. The hydro button is different: press it once to start and once again to stop. On tubs with foot jets, the panel turns the foot jet pump on and off too.
If you tapped the air icon several times and the bubbles kept going, press and hold instead. The in-line heater has no control of its own. It runs only while the hydro pump runs, so stopping the hydro also stops the heater. Each gesture is laid out function by function in How Do I Use Every Function on the Ella Digital Control Panel?
If the panel does not react to any touch at all, the touchpad plugs into the display connector on the control box, and a cable that is not fully seated there is worth checking with the power off.
If the Pumps Still Run and the Panel Stays Dead
When the Auto Purge has been ruled out, no button is stuck, the gestures are right and the pumps still keep running with an unresponsive panel, the cause can be a stuck relay or the control board. Leave the power off at the breaker and contact your Ella dealer or the team at (800) 480-6850, or open a ticket at ellasbubbles.com/support. Have these ready:
- Your model name and serial number.
- Whether the tub has push buttons or the digital touchpad, with a photo of the controls.
- Which pump kept running, and which buttons or icons respond and which do not.
- Whether the pump stopped by itself after about two minutes, or only when the breaker was switched off.
A touchpad that has genuinely failed is replaced as a single part, and none of the pumps need to come out to do it. Ella does not send technicians. Replacement parts ship under the warranty after the team verifies the problem, and a local licensed electrician does the work. If you later find the opposite problem, a pump that will not start once power is back on, the water level, breaker and GFCI checks are in Why won't my walk-in tub's air or whirlpool pump turn on?

Watch: Walk-In Tub With Air Massage & Auto-Purge Technology for Self-Cleaning | Ella's Bubbles with chapters and a full transcript.
Related Videos

