Support Center / Therapies & Operation / How Do I Adjust Jet Pressure and Air Controls for Therapeutic Massage?
Back to Therapies & Operation

How Do I Adjust Jet Pressure and Air Controls for Therapeutic Massage?

On an Ella walk-in tub you adjust hydro jet pressure with the intensity control dial on the deck, and you adjust the air massage by stepping through its speeds: the first press is high, the second is medium, the third is low, and a fourth press turns it off. Foot jets have a third adjustment of their own, a center nozzle that turns like a valve. What Do I Do If My Walk-In Tub Jets Are Too Strong? is the troubleshooting page for jets that push too hard, and this page covers every control in one place so you can set the massage the way you like it.

Know Which System You Are Adjusting

The two massage families work differently, so they are adjusted differently. An air massage system moves air rather than bath water through the air jets. A hydro massage system draws bath water through a pump and pushes it back out through the water jets. Each system on an Ella tub has its own pump under the seat, and Ella does not use a diverter to split one pump between systems, so every system you ordered can run at the same time and each one is set on its own.

Ella's component diagrams print the adjustment next to each system, which is a handy way to see what your tub has:

  • Air massage: printed as a Variable Speed Pump with Auto Purge. You change the speed.
  • Seat hydro massage: printed with a Hydro Pump and a Hydro Massage Air Flow Intensity Control. You turn the dial.
  • Hydro foot massage: on tubs with independent foot massage, it has its own Hydro Pump, its own ON/OFF button and its own Hydro Massage Air Flow Intensity Control.

What is a therapeutic bath in a walk-in tub? describes what each system does for the bather. The steps below are about the controls themselves.

Adjusting Hydro Jet Pressure with the Intensity Dial

The intensity dial does not change the pump. It changes how much air is mixed into the jet stream. Turning the dial up introduces more air into the stream for a stronger flow, and turning it down reduces the air for a more gentle flow, all the way down to where the massage is barely noticeable.

  1. Fill the tub to 2 inches above the highest jets before starting the hydro, so the jets push through water instead of spraying.
  2. Start the hydro massage. On push controls it starts with one touch of the water button. On the digital touchpad, press the hydro button once.
  3. Turn the intensity dial slowly while the hydro runs and feel the change. Turn it down for a softer massage and up for a firmer one.
  4. To stop, press the hydro button once again.

The dial works the same way whichever control style your tub has. The digital touchpad switches the hydro massage on and off, and the intensity is still adjusted with the dial. If the dial will not move, do not force it. Send a photo through ellasbubbles.com/support so the team can confirm whether it needs attention.

Two things happen on their own while the hydro runs, so there is nothing to set. The in-line water heater runs automatically with the hydro pump, and the ozone sanitation system is automatic as well.

Adjusting the Air Massage on Push Controls and the Touchpad

The air massage has three speeds, and the order surprises many new owners because it starts at the top. The first video on this page shows both control styles in use.

On the ON/OFF push controls, which need only a gentle push:

  • First press: high speed.
  • Second press: medium speed.
  • Third press: low speed, which gives the softest bubbles.
  • Fourth press: off.

On the digital touchpad:

  • Touch the air bubble icon once to start the air massage.
  • Touch the plus button to increase the intensity.
  • Touch the minus button to decrease the intensity.
  • Hold the air bubble icon down for two seconds to turn the air massage off.

If the air jets feel too strong in the seat, the answer is the third press on push controls or the minus button on the touchpad. Individual jets cannot be permanently closed off, because removing an air jet lets air escape from the system.

One more air behavior is automatic. The Auto Purge activates 20 minutes after the air pump is turned off and runs for 120 seconds to blow residual water out of the air lines. It is fully automatic, it cannot be stopped, and it is normal even if it starts while you are still in the tub.

Fine-Tuning the Foot Jets at the Nozzle

Foot jets carry an adjustment right at the jet. The second video shows a technician adjusting a foot jet when the pressure is too low or too high, and the key point is that the center nozzle is a valve that opens and closes the jet.

  1. Turn the center nozzle of the foot jet to raise or lower its pressure.
  2. If the nozzle is too hard to turn, loosen the butterfly handles behind the jet. The video shows them being loosened with a pair of pliers, which releases the center nozzle so it turns left or right.
  3. To be sure the valve is fully open, look at the jet's half cut opening and line it up with the hole inside, where the water comes out.
  4. Tighten the nut for the jet so the nozzle stays put and does not turn on its own.

On tubs ordered with independent foot massage, the foot system also has its own pump, button and intensity control, as drawn in What the Air + Hydro + Hydro Foot Schematic Shows. That gives you two levels of control: the dial sets the whole foot system, and each nozzle sets its own jet.

Putting the Controls Together for a Comfortable Bath

Because every system has its own pump, you can set each one separately and run them together. A few points keep the session comfortable:

  • Water level first. A low water level makes jets spray rather than push through water, which feels harsher and sends water out of the tub. Fill before you start the hydro.
  • Set each system on its own control. The dial changes only the hydro stream, and the air button or the plus and minus buttons change only the air massage.
  • Adjust your seating position. If the back jets push you forward, turn the dial down and shift how you sit against them.
  • Microbubbles are switched separately. In the triple therapy package the air and seat hydro run from the digital controller, while the microbubble system keeps its own push button, as shown in What the Air + Hydro + Micro Schematic Shows.
  • The chromatherapy light works the same on both control styles. Press the button once for the full range of colors, press again to select a specific color, and hold for two seconds to turn the light off.

If the dial will not turn at all, or a foot jet nozzle stays seized after the butterfly handles are loosened, open a ticket at ellasbubbles.com/support or call your Ella dealer or the team at (800) 480-6850. Include your serial number and a photo of the dial or the jet in question so the team can confirm the cause.

Watch: How to Adjust to Hydro Jets in Your Walk-In Tub? | Ella's Bubbles with chapters and a full transcript.

Video

Common Questions

Why does my air massage start on the strongest setting?
That is how the three-speed air control is designed. The first press is high speed, the second is medium, the third is low, and a fourth press turns the system off. Press to the third setting for the softest bubbles.
What does the intensity dial on the tub deck actually change?
The dial controls how much air is mixed into the hydro jet stream. Turning it up introduces more air for a stronger flow, and turning it down reduces the air for a more gentle flow. At its lowest the massage is barely noticeable.
How do I adjust the pressure on a single foot jet?
Turn the center nozzle of the foot jet, which is a valve that opens and closes the jet. If it is too hard to turn, loosen the butterfly handles behind the jet, set the nozzle, then tighten the jet nut so the nozzle stays in place.
Does the digital touchpad change the hydro jet pressure too?
The touchpad turns the hydro massage on and off with one press of the hydro button. The intensity of the hydro massage is still adjusted with the intensity control dial. The plus and minus buttons adjust the air massage.
Can I close off one jet that feels too strong?
Individual jets cannot be permanently closed off, because removing an air jet lets air escape from the system. Use the low air speed, the intensity dial and the foot jet nozzles instead. Between those three adjustments, almost every owner finds a comfortable level.
Why do the air jets run by themselves after my bath?
That is the Auto Purge. It activates automatically 20 minutes after the air pump is turned off and runs for 120 seconds to blow residual water out of the air lines. It cannot be stopped and it is normal.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket