Support Center / Walk-In Tub Models / What Is a Walk-In Tub and How Does It Work, From Door to Drain?
Back to Walk-In Tub Models

What Is a Walk-In Tub and How Does It Work, From Door to Drain?

Updated November 2026

A walk-in tub is a bathtub with a watertight door built into its side wall and a seat molded inside. Instead of climbing over the high wall of a regular bathtub, you step through the door over a low lip, the step-in threshold on a walk-in tub, and sit down. You get in while the tub is empty, close and lock the door, and fill the tub from the faucet while seated. Then you enjoy the soak or the massage systems and drain the tub completely before you open the door and step out. Because the tub fills after you are seated, you use less water than the tub holds when empty. How much water does a walk-in tub actually use per bath? breaks this down model by model. On an Ella's Bubbles tub the fast-fill faucet and the 2-inch gravity drains keep both ends of that routine short, as explained in Drainage and Fill Time. Every Ella tub is assembled and tested to order before it ships. Walk-In Tub Versus a Regular Bathtub: Seven Practical Differences in Entry, Seating, Fill and Drain, Water Use, Electrical, Installation and Cleaning compares the two tub types.

The Parts of a Walk-In Tub and What Each One Does

Every Ella walk-in tub is built from the same handful of parts, and once you know them the rest of the routine is obvious. The door, the seal, the frame and the threshold are engineered together as one complete unit.

  • The door. Depending on the model, the door swings inward into the tub or outward into the room. The Standard, Zen and Zen60 use an inward-swing acrylic S-shape door. The Capri, Monaco, Front Entry, Mobile, Lounger, Shak and Big4One use an outward-swing U-shape door made of plastic composite and tempered glass with a 3-latch gear and shaft mechanism, and the Tub4Two uses the same outward-swing style with a frosted glass panel in a white composite frame. The Transfer family uses an L-shape outward-swing door with two latches that clears the whole side of the tub for a wheelchair transfer. The door closes on an integrated gasket. Ella does not offer a lift-up or drop-down door. The door swings open like any other door.
  • The low threshold. Instead of swinging a leg over the 18 to 22 inch wall of a standard bathtub, you step over a low sill. On Ella tubs it runs roughly 3.5 to 7 inches, depending on the model and how the drain is set up. The low threshold itself is the accessibility feature.
  • The seat. You bathe sitting upright on a built-in seat with a backrest, set at a comfortable chair height, so you never lower yourself to the floor of the tub and you stand up from seat height at the end of the bath. Ella seats run from 19 inches wide on the Petite to 29 inches on the TransferXXL, and the floor is textured and slip resistant. On tubs with air massage, the jets are set into the seat, the base of the seat and the footwell floor, so the massage reaches you where you sit.
  • Grab bars. Nearly every Ella model has a built-in grab bar as standard equipment. It gives you something solid to hold as you step in, sit, soak and stand.
  • The faucet. A deck-mounted fast-fill faucet with a pull-out hand shower is part of the tub package. On the Standard it is the 5-piece Ella Fast-Fill faucet with hot and cold handles, a diverter lever and the pull-out hand shower. You choose the faucet when the order is placed, and the tub is drilled for it. The choices include the two-piece high-flow faucet, the five-piece high-flow faucet and the TCV faucet. A tub with the Ella thermostatic faucet package includes a built-in Thermostatic Control Valve that mixes hot and cold to a set temperature.
  • The drains. Ella tubs drain by gravity through 2-inch drains with overflows, and there is no drain pump. Most models carry two 2-inch drains, and the Standard ships with one 2-inch gravity floor drain with an overflow and an emergency pull-up chain. The drains sit on the same side of the tub as the door: a right-side door tub has its drains on the right, and a left-side door tub has its drains on the left as you face the tub. The fast-fill faucet and the gravity dual drain are designed to work together, so the tub fills and empties around a seated bather.
  • The shell, the frame and the access panel. The acrylic shell sits on a rustproof stainless steel frame, and the tub ships with ground wires on the frame and on every electrical component. A magnetic access panel next to the door covers the label that carries the serial number. In the first video below, the presenter explains why acrylic matters. It is one solid piece of material over the entire bathtub, it is very low maintenance, and if the surface ever gets dull it can be buffed right out. The presenter contrasts this with fiberglass, a multi-layer system built up from a gel coat, and describes its finish as brittle.

This is also why a door cannot simply be added to an ordinary tub. None of these parts can be fitted to a standard bathtub after the fact, as Can Ella Cut a Walk-Through Opening or Add a Door to My Existing Bathtub? explains.

How a Bath Works from Start to Finish

The order never changes, because the door is closed before the water goes in and opened only after the water is gone.

  1. Open the door, step over the low threshold using the grab bar, and sit down on the seat.
  2. Close the door and lock it. On an outward-swing door the handle drives the latches into the frame and compresses the seal. On an inward-swing door the water presses the door shut once the tub fills.
  3. Close the drains and open the faucet. The fast-fill faucet delivers about 16 gallons per minute, so a tub with a capacity of around 60 gallons fills quickly. Your home water heater does the heating, so fill with comfortably hot water from the start.
  4. Once the water is 2 inches above the highest jets, switch on the hydro massage. Air jets must also be fully under water before the blower starts.
  5. Soak for as long as you like, keeping the bath water at or below 100.4 degrees Fahrenheit.
  6. When you are finished, turn the systems off and open the drains. Stay seated while the water drains. Connected to a proper 2-inch drain line, most Ella tubs empty in two minutes or less. Drain speed depends on the drain line under the tub as much as on the tub itself, so a licensed plumber should connect it to a 2-inch line.
  7. Wait until the tub is completely empty, then open the door and step out over the threshold. Never open the door with water still in the tub.

For a bather who uses a wheelchair and bathes with a caregiver's help, the start and end of the sequence change. The Ella HomeCare is the model built for that situation. The bather rolls up to the tub in the wheelchair and transfers in with the caregiver's help. The caregiver moves the wheelchair away, closes and locks the door, and then fills the tub with the fast-fill faucet. Despite the name, Ella's Home Care is a tub model, not a home care agency. On the Transfer models, wheelchair users usually transfer across the seat rather than stepping over the threshold, so the L-shape door opening matters as much as the lip on those tubs.

Filling a Walk-In Tub: Where the Hot Water Comes from

The most common surprise for new owners is how much hot water a seated bath uses. Depending on the model, a walk-in tub takes roughly 55 to 75 gallons or more to fill once you are seated. A 40 gallon home water heater does not hold that much hot water, so it can run cold about halfway through the fill. Ella's Bubbles recommends a 75 gallon or larger tank, or a tankless unit rated around 11 gallons per minute. A 40 gallon tank can work only if nothing else draws hot water at the same time. The largest single-seat tub, the ShaK, may need a dedicated additional heater. If your bath goes lukewarm before it is full, Why Does My Hot Water Run Out Before the Tub Is Full? walks through what to check.

Every Ella spec sheet prints water capacity as two numbers. Unoccupied capacity is what the tub holds with nobody in it. Occupied capacity, written as a range, is what you actually use once you are seated and your body is displacing water. Most standard-size Ella walk-in tubs hold 65 to 107 gallons unoccupied. The Standard, for example, holds 65 gallons unoccupied, and the two-seat Escape holds 145 gallons. A smaller bather typically uses the upper end of the occupied range and a larger bather the lower end. Fill time is the capacity divided by the real-world flow at your faucet, so the occupied figure is the better guide when you estimate a fill.

The in-line water heater under a hydro massage tub is not a substitute for a hot fill. It maintains the bath temperature while the hydro pump runs and never raises the temperature of water that arrived cool. Keep bath water at or below 100.4 degrees Fahrenheit.

How the Massage Systems Work

Walk-in tubs are built as soaking tubs or with therapy packages, and the two main systems work very differently. The therapies are separate systems under the tub.

  • Hydro massage uses a pump that pulls bath water through an in-line heater and pushes it back out through jets in the seat and footwell. The Standard, for example, ships with 18 hydro jets, a push control and an intensity dial. Because the water loops through the heater, the bath holds a steady temperature for a long soak. The heater switches on and off with the pump, so there is no heater button and no thermostat to set. Typical spec sheet ratings are 6A 650W on the Standard, Zen and Flow, 5.5A 650W on the Elite and Petite, and 9A 1000W on the Ultimate's foot loop. What Is an In-Line Water Heater on a Walk-In Tub? explains the loop in detail.
  • Independent foot massage. On tubs with this feature, the heater is attached to the foot massage pump, so running the foot jets is what keeps the water warm.
  • Air massage uses a three-speed blower that pushes air through small brass jets in the seat, the base of the seat and the footwell floor for a gentle bubble massage. It has no heater. Press the Air button once for high, twice for medium, three times for low and a fourth time to turn it off. About 20 minutes after you switch the air pump off, Auto Purge starts on its own and runs for 120 seconds to blow residual water out of the air lines. It cannot be stopped and is normal even if it starts while you are still in the tub. What Are Air Massage Jets on a Walk-In Tub? shows where the jets sit.
  • Extras such as the LED chromatherapy light, a heated seat and backrest, aromatherapy and head pillows add comfort without changing how the tub itself works. The glossy acrylic shell acts like an insulator, and an optional heated seat adds warmth while the water rises. The Walk-In Tub Accessories and Add-Ons guide lists what can be chosen with the tub.

Most models also come as a soaker with no jets. Air-only and soaking tubs have no hydro pump and no heater, and a soaking tub works simply as a deep, seated soak. Because the jets and air lines are built into the shell at the factory, a massage system cannot be added later, so decide on therapy when you order. The pumps are why a therapy tub needs an electrician as well as a plumber.

Where the Threshold Number Comes from

The threshold height is really the height of the tub floor above the finished bathroom floor. The tub sits on adjustable leveling legs, and the drawings on each spec sheet show the factory frame height with the legs at their standard setting. Two things move that number. A recessed drain lets the tub sit lower, and a different leg setting raises or lowers the frame. So the figure on the drawing is the starting point, and your installation decides the final height.

Every Ella walk-in tub has a low threshold, and the published figures vary by model. Drawing values include the Monaco at 3 5/8 inches and the Mobile at about 3 3/4 inches. Team figures put the Transfer32 at about 4 to 4.5 inches, the Big4One and ShaK at about 5 inches, the Ultra at about 6, and the Elite at about 6.5. If a lower step matters to you, talk with your installer before the tub goes in. Thresholds can be reduced to about 3 to 3.5 inches by setting the tub lower with the drain below the subfloor. Cutting the apron or end panel to make that work voids coverage on those altered panels only. After installation, keep an eye on the leveling legs. A leg that loses contact with the floor can warp the frame and throw the door out of alignment, and a walk-in tub door cannot tolerate being out of alignment.

Where a Walk-In Tub Goes in Your Bathroom

Most Ella walk-in tubs go into the same three-wall opening your current bathtub occupies, which is what an alcove installation for a walk-in tub means. This way you keep the room's layout and plumbing locations. The tub is enclosed on the back and both ends, with only the front apron exposed. Most bathrooms were framed around a 60 inch bathtub, so that is the opening you are usually filling. Tubs that are 60 inches or longer fill the space on their own. The Ultimate is actually 59.5 inches, which is why it needs no extension panel. Most 52 and 55 inch models fill the remaining space with an Ella extension panel that mounts at the end of the tub frame, so the finished installation looks built in. A knee wall can hide the plumbing or carry fixtures. The walls above the deck are then finished with tile or a surround over an aftermarket tile flange so water runs back into the tub.

Ella tubs are not limited to alcoves. The same models can stand against one or two walls with an end panel closing the exposed side. Whatever the layout, ask your installer to add a wall access panel behind the plumbing end so pumps and drain connections can be reached without disturbing tile. Never let the space around the tub be packed with insulation. Ella tubs use their own deck-mount faucet packages, so your existing tub spout and handles are normally replaced rather than reused.

What Keeps a Walk-In Tub Safe and Clean

The electrical side is simple from the bather's point of view. The pumps and controls run from the home's electrical supply, and the tub ships with ground wires on all electrical components and on the frame so your electrician can ground it to local code. Ella's Bubbles does not send technicians: a local licensed plumber and electrician install the tub. The warranty covers parts. The shell, frame, door, door seal and finish carry a lifetime limited warranty, and supporting equipment such as the in-line heater carries a 5-year parts warranty. If a part ever fails during the 5-year parts warranty, the replacement part ships to you and a local tradesperson fits it.

Cleaning the massage plumbing is a monthly routine rather than a daily one. Combine 2 cups of white vinegar with 2 cups of water, fill the tub to one inch above the highest jets, add the mixture, run the tub for 10 minutes, then drain. Do this once before the first bath and once a month afterward. Flushing after every bath is not necessary.

Surface care is the second habit. The shell is one solid piece of acrylic that polishes back to a shine. Use non-abrasive cleaners and lift stubborn marks with denatured alcohol. To restore light scratches or dull spots, use a fine automotive polishing compound such as a Turtle Wax product, working in small circles with a soft cloth. Abrasive cleansers and scrubbing pads are the one thing that will permanently damage the gloss. Scratches, Scuffs, or Discoloration on the Acrylic: Surface Care and Touch-Up Kits has the full method. If anything in the sequence above does not match what your tub is doing, open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your model and serial number.

What a Walk-In Tub Is Not, and Who Installs It

A walk-in tub is not a modification of the tub you already have. Ella's Bubbles does not cut a walk-through opening or add a door to an existing bathtub, and there is no Ella cut-in kit or conversion product. A purpose-built walk-in tub gives you a sealed low door, a seat and grab bars that were engineered together, rather than an opening in a tub that was never designed to have one.

Ella's Bubbles does not install the tub either. Ella manufactures the tub, and a licensed, experienced local contractor installs it, with technical support from Ella available to guide the work. If you do not have someone in mind, Ella's Bubbles can send your installation lead to a recommended contractor in your area, as explained in getting installer referrals for your walk-in tub. The installer receives your contact information, the tub specifications and the electrical diagrams for your model ahead of time. They then contact you directly, visit your home to measure the space and give you an estimate for the work. To get started, reach your Ella dealer or the team at (800) 480-6850, or open a ticket at ellasbubbles.com/support with your installation address.

Video
Chapters in this video
  1. 0:00 Lifetime Warranty And Service Ella's Bubbles offers a lifetime warranty on all bathtubs and installations, emphasizing excellent service.
  2. 0:14 Acrylic Bathtub Construction Ella's Bubbles walk-in tubs are made from a single piece of durable acrylic, preventing chipping or cracking.
  3. 0:49 Low Maintenance Acrylic Acrylic bathtubs are very easy to maintain and require minimal service, as dull spots can be buffed out.

Watch: Acrylic Over Fiberglass: The Better Walk-In Tub Choice | Voted Safest/Best 2020 | Ella’s Bubbles with chapters and a full transcript.

Video
Chapters in this video
  1. 0:00 Choosing Your Walk-In Tub Faucet We discuss the importance of selecting the right faucet for your Ella's Bubbles walk-in bathtub.
  2. 0:21 Customizing Your Bathtub Order We explain how each Ella's Bubbles bathtub is custom-drilled and installed with your selected faucet and features.
  3. 0:39 Competitor Faucet Limitations We highlight that other brands typically offer limited or no faucet options for their bathtubs.

Watch: Luxury Faucet Options for Your Walk-In Tub, Voted Best/Safest 2020 | Ella’s Bubbles with chapters and a full transcript.

Video
Chapters in this video
  1. 0:00 Why Choose Ella's Bubbles Ella's Bubbles saves customers money by avoiding large corporate overhead and offering transparent pricing.
  2. 1:26 Key Questions for Walk-in Tubs Customers learn important questions to ask when shopping for a walk-in tub, including design, installation, and warranty.
  3. 2:21 Virtual Showroom and Product Range Ella's Bubbles offers live video chats and a virtual showroom to explore their wide range of walk-in tub models and sizes.
  4. 3:28 Fast Fill and Drain Systems The video highlights Ella's walk-in tubs' strategic jetting, fast-fill faucets, and industry-leading quick drain system.
  5. 4:10 Accessories and Customer Satisfaction Ella's Bubbles offers various accessories to enhance the walk-in tub experience, and customers can view testimonials online.
Video
Chapters in this video
  1. 0:00 Staying Warm While Filling The video addresses concerns about getting cold while filling and draining a walk-in tub.
  2. 0:37 Heated Seats for Added Warmth The video explains how to use the optional heated seats for extra comfort.
  3. 0:54 Fastest Gravity-Driven Drains The video highlights the quick draining capabilities of Ella Tubs with dual oversized drains.
Video
Chapters in this video
  1. 0:00 Considering Your Personal Needs The video discusses important factors to consider when choosing an Ella's Bubbles walk-in tub, including personal needs and mobility.
  2. 0:40 Measuring for Proper Tub Fit The video explains how to take shoulder, hip, and overall body measurements to ensure the walk-in tub fits properly.
  3. 2:26 Home Accommodation and Placement The video advises checking door widths and hallways to ensure the chosen tub will fit into the home and bathroom.
  4. 4:17 Ensuring Proper Water Supply The video recommends having a maximum capacity water heater and three-quarter inch supply lines for the walk-in tub.
  5. 4:47 Designing Your Walk-In Tub The video details how to choose jetting packages, including air, hydro, and MicroBubble therapy, and other innovative features.
  6. 6:15 Adding Optional Accessories The video showcases various accessories like heated seats, digital controls, headrests, and a four-fold glass screen.
Video
Chapters in this video
  1. 0:00 Outward Swing Door Design The video introduces the robust vault-like design of Ella's Bubbles outward swing walk-in tub doors, featuring oversized tapered pins for a secure seal.
  2. 1:26 Easy Door Operation The video demonstrates how easy it is to close and operate the outward swing door, highlighting the tapered pins that do all the work.
  3. 2:01 Accessibility and Peace of Mind The door is designed for ease of use, even with limited mobility, providing maximum peace of mind that the seal will never leak.
Video
Chapters in this video
  1. 0:00 Ella's Dual Drain Technology Ella's Bubbles walk-in tubs feature exclusive dual drain technology with oversized two-inch drains for efficient water removal.
  2. 0:17 How Dual Drains Work The video explains how Ella's dual two-inch drains connect to a house drain, offering maximum draining capacity.
  3. 0:47 Connecting to Your House Drain The video demonstrates connecting the tub's dual four-port t-type drains to a house drain on either the left or right side.
  4. 1:14 Dual Air Vents and Gravity Easy-turn drain handles double as air vents, eliminating air pockets and maximizing water outflow through a gravity-driven system.
Video
Video

Common Questions

How do you fill a walk-in bath once you are inside?
Sit down, close and lock the door, close the drains and open the deck-mounted faucet with comfortably hot water from your home water heater. The fast-fill faucet delivers about 16 gallons per minute, so a tub of around 60 gallons fills quickly. On a tub with the Ella thermostatic faucet package, the built-in Thermostatic Control Valve mixes hot and cold to a set temperature. If your tub has hydro massage, wait until the water is 2 inches above the highest jets before switching it on.
Do you have to sit in an empty tub while it fills and drains?
Yes, that is how every walk-in tub works, because the door is part of the tub wall and must be closed before filling and opened only after draining. You step in, sit, latch the door and then fill, which is why the water you use per bath is the smaller occupied figure on the spec sheet. The fill rate of about 16 gallons per minute and a drain time of two minutes or less on a proper 2-inch line keep both waits short.
Does the door leak when the tub is full of water?
No, because the door closes on an integrated gasket, and the door, seal, frame and threshold are engineered together, with every tub assembled and tested to order before it ships. An outward-swing door uses a gear and shaft mechanism that pushes latches into the frame and compresses the seal evenly, and an inward-swing door is pressed shut by the water itself. Keep the seal clean and let the tub drain completely before opening the door. The door and door seal are covered under the Lifetime Limited Warranty.
Can a walk-in tub reheat the water if it gets cold?
No. Your home water heater heats the fill, and the in-line heater on a hydro massage tub only maintains the temperature of water that was filled hot, running only while the hydro pump runs. Air massage has no heater at all, so fill from a hot water supply sized for the bath and keep the water at or below 100.4 degrees Fahrenheit.
Does Ella's Bubbles install the walk-in tub for me?
No. Ella's Bubbles builds the tub, and a local licensed plumber and electrician install it. If you do not have someone in mind, Ella's Bubbles can send your installation lead, along with the tub specifications and electrical diagrams, to a recommended contractor in your area, who contacts you directly, measures the space and provides an estimate. Technical support is available to you and your contractor through ellasbubbles.com/support and (800) 480-6850, and parts ship under the warranty while your tradesperson does the labor.
How do I keep the jets and lines clean inside?
Once a month, combine 2 cups of white vinegar with 2 cups of water, fill the tub to one inch above the highest jets, add the mixture, run the tub for 10 minutes and drain. On air massage tubs the Auto Purge also blows the air lines dry automatically after each bath.
Why does the air system turn on by itself after my bath?
That is Auto Purge. It activates automatically about 20 minutes after the air pump is turned off and runs for 120 seconds to blow residual water out of the air lines. It cannot be stopped and it is normal, even if it starts while you are still in the tub.
Can my existing bathtub be turned into a walk-in tub?
No. Ella's Bubbles manufactures complete walk-in bathtubs and does not cut an opening, add a door or gate, or alter an existing tub or tub and shower combination, and there is no Ella cut-in kit or conversion product. The door, seal, frame and threshold are engineered together, so a purpose-built walk-in tub gives you a sealed low door, a seat and grab bars that were designed to work together.
How much water does one walk-in tub bath use?
Depending on the model, a walk-in tub takes roughly 55 to 75 gallons or more to fill once you are seated, while most standard-size Ella tubs hold 65 to 107 gallons with nobody in them. The amount varies with bather size, because your body displaces part of the water.
How do you get out of a walk-in tub safely?
Open the drain and stay seated until the tub is empty, then open the door and step out over the low threshold, using the grab bar. Most Ella tubs drain through two 2-inch gravity drains in two minutes or less when connected to a proper 2-inch drain line.
How long does a walk-in tub take to drain?
An Ella tub with two 2-inch gravity-driven drains typically empties in two minutes or less once it is connected to a proper 2-inch drain line. There is no drain pump, so the speed depends on gravity and on the drain line your plumber installs.
How is a walk-in bathtub different from a regular bathtub?
A regular bathtub asks you to swing a leg over an 18 to 22 inch wall and lower yourself to the floor of the tub. A walk-in tub replaces that with a door, a threshold of roughly 3.5 to 7 inches on Ella models, a built-in seat at a comfortable height and grab bars. You sit, close the door, and fill the tub around you.
Does the door on an Ella walk-in tub lift up or drop down?
No. Ella does not offer a lift-up or drop-down door. The door swings open like any other door and closes on an integrated gasket, and the low threshold itself is the accessibility feature.
Will a walk-in tub fit where my current bathtub sits?
Every Ella model fits the classic three-wall alcove, and most bathrooms were framed around a 60 inch tub. Tubs 60 inches or longer fill the opening on their own, the Ultimate at 59.5 inches needs no extension panel, and most 52 and 55 inch models use an Ella extension panel at one end. Plan around the actual size on the spec sheet rather than the nominal name.
Is Ella's Home Care a separate company or an agency?
No. Ella HomeCare is the name of one bathtub model made by Ella's Bubbles, built for wheelchair users who bathe with a caregiver's help. It is listed under the assisted bathtubs and equipment category and is not affiliated with any outside business.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket