Support Center / Door & Seal / How do I re-seat the door gasket on an Ella LayDown tub?
Back to Door & Seal

How do I re-seat the door gasket on an Ella LayDown tub?

On an Ella LayDown tub the door gasket re-seats the same way it does on any Ella door: clean the seal and the door frame with a common household cleaner, then press the lifted section fully back into its groove, with no sealant to start. The gasket is held by its fit and not by adhesive, so a section resting on the edge of the channel will keep popping out until it sits inside it. The general procedure is in How do I re-seat the door gasket on my walk-in tub?, and this page applies it to the LayDown glass door.

Know the LayDown Door Before You Start

The LayDown60 and LayDown72 share their own door family: tempered glass in an aluminum frame with a lift-up bar lock. The LayDown60 spec sheet describes it as a unique tempered glass inward swing door with a brushed-finish aluminum frame. That matters for two reasons.

  • The seal is specific to this door. The LayDown glass door uses its own seal, so a gasket from another Ella door family is not a substitute. If you ever need a new one, it is matched to your model and serial number.
  • The swing direction decides where silicone may go. Ella's door seal maintenance video gives a separate step for inward swing doors, described below. The supplied spec sheet confirms inward swing for the LayDown60. If you own a LayDown72, check which way your door swings and mention it when you contact the team.

The serial label is behind the removable panel, and the serial number tells the team when the tub was built and which parts are compatible. Photograph it before you begin so it is ready if you need help.

Rule Out the Look-Alikes First

Several problems look like a gasket that needs re-seating but have a different fix.

  • Water along the bottom edge of the door. The number one cause of a door leak is a leveling leg that has lost contact with the floor. That warps the frame so the door no longer meets the seal evenly, and pressing on the gasket will not cure it. Have every leveling leg checked first. The LayDown has a stainless steel frame with adjustable leveling legs.
  • A tacky or sticky seal. Residue is the usual cause. Wipe the seal and frame with a household cleaner, and if the gasket still feels tacky or looks flattened, wipe it with rubbing alcohol. No oil, grease or spray lubricant is called for.
  • Debris in the seal or the frame. Any residue that is allowed to build up, and any debris left in the seal or the door frame, can lead to a door leak on its own.

If the legs are solid, the seal is clean and you can see a section of gasket lifted out of its groove, re-seating is the right step.

Step by Step: Re-Seating Without Sealant

  1. Open the door and find the lifted section. It is usually near the top or at a curve, where closing the door pushes out any part of the gasket that sits on top of the groove instead of inside it.
  2. Clean the groove and the frame. Use a common household cleaner and a soft cloth so nothing sits under the gasket. Run a fingertip along the channel to feel for anything left behind.
  3. Reshape a flattened section. Squeeze and reform any part of the gasket that has been pressed flat.
  4. Press the gasket fully into its channel. Use your thumbs or a plastic spatula and work along the whole lifted length until the gasket is inside the groove, not resting on its edge. Do not use a metal tool that could scratch the door.
  5. Let it rest. Leave the door ajar for about a day before refilling, so the gasket is not compressed while it settles.

Most gaskets stay put after this, with no sealant at all.

If the Gasket Will Not Stay Seated

Silicone is sanctioned by Ella's own door seal maintenance video, which is on this page. It is ordinary hardware-store silicone sealant, and no brand, grade or color is specified, as Which Silicone Should I Use to Reseat a Walk-In Tub Door Gasket? confirms. The video shows two methods:

  • A loose section that has been removed. Run a thin bead of silicone into the gasket channel, allow it to set up for 20 minutes, press the gasket back in, then wait 24 hours for the silicone to dry before the door sees water.
  • An inward swing door, such as the LayDown60 glass door. Roll the gasket away from the frame and run a bead of silicone down the corner where the gasket meets the frame. Add a bead to the other side of the gasket if necessary, and again wait 24 hours.

One rule covers every door: never spread caulk or silicone across the sealing face the door closes against. The seal works by closing against a clean surface, and sealant there prevents it from doing its job.

When Re-Seating Is Not Enough

If the gasket is torn, permanently deformed or keeps working out of the channel after re-seating, the seal itself is the part to replace. The second video on this page shows a full seal installation on an Ella door: adhesive remover sprayed on the gasket so it slides into the channel, a spatula to seat it, relief cuts at the curves and a small angled cut at the end point. The LayDown glass door has its own support video for this job, and Video Guide: Installing a Replacement Door Seal, Including the LayDown Glass Door explains how the working principles carry over. The gasket must sit fully in its channel along the whole loop, any silicone must cure before the tub is filled, and the door is water-tested for 20 minutes and then left ajar.

The door and the door seal are covered by our Lifetime Limited Warranty. If the door still leaks after leveling and re-seating, open a ticket at ellasbubbles.com/support with your model, serial number and photos. Once the defect is verified, the model specific seal ships to the original customer's address without charge. Ella does not send technicians, so a local licensed plumber or handy helper does the work on site.

To find the other clips for your door, Every Ella Door Video in One Place groups them by door family, with the LayDown glass door listed on its own.

Keeping the Gasket Seated

Leaving the door slightly open when the tub is not in use is what keeps most seals from needing any of this. It prevents unnecessary compression of the gasket and extends its flexibility and life. Add a regular wipe of the seal and the door frame with a common household cleaner, and the gasket has very little reason to lift.

Watch: How To Install a Walk-In Tub Door Seal (Step-By-Step) with chapters and a full transcript.

Common Questions

Do I need silicone to re-seat the LayDown door gasket?
Usually not. The gasket is held by its fit in the groove, so cleaning the seal and frame and pressing the lifted section fully back in is the first step. Silicone comes in only when a loose or damaged seal will not stay seated.
Which type of silicone does Ella specify for the door gasket?
Ella does not specify a brand, grade or color. The door seal maintenance video calls for ordinary silicone sealant, the kind sold at a hardware store, applied as a thin bead.
Where does the silicone go on an inward swing door?
Roll the gasket away from the frame and run a bead of silicone down the corner where the gasket meets the frame. A bead can be added to the other side of the gasket if necessary. Wait 24 hours for it to dry.
Can I run caulk over the seal to stop a leak?
No. Never spread caulk or silicone across the sealing face the door closes against. A leak along the bottom edge usually points to a leveling leg that has lost contact with the floor, so have the legs checked first.
Is the LayDown door seal covered by the Ella warranty?
Yes. The door and the door seal are covered by the Lifetime Limited Warranty. Open a ticket at ellasbubbles.com/support with your model, serial number and photos, and once the defect is verified the model specific seal ships to the original customer's address without charge.
How do I keep the gasket from popping out again?
Leave the door slightly open whenever the tub is not in use, which prevents unnecessary compression of the gasket. Clean the seal and the door frame regularly with a common household cleaner so residue and debris do not build up.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket