Support Center / Sizes, Fit & Measuring / What Is the Smallest Shower Pan Size You Can Buy from Ella's Bubbles?
Back to Sizes, Fit & Measuring

What Is the Smallest Shower Pan Size You Can Buy from Ella's Bubbles?

Updated November 2026

The smallest shower pan Ella's Bubbles makes is a custom acrylic base measuring 30 by 30 inches, and that minimum applies to both three-wall alcove bases and corner bases. The smallest pan in the standard lineup is 30 by 60 inches, so any square or short footprint is a custom request instead of a stock size. The complete range is laid out in What sizes do shower pans come in, from smallest to largest?, and this page stays at the small end of that range: how small a pan can go, what sets the limit, and how to plan a compact shower around it.

The Two Smallest Sizes: Custom and Standard

There are two honest answers to this question, and the one that applies to you depends on whether you want a pan made to order or a pan from the standard lineup. Some people have a compact space and want to know how small a base can go. Others have a regular tub alcove and want the narrowest pan that is available as a standard size. It helps to know both answers before you measure.

The custom shower base page lists a minimum of 30 by 30 inches, and that floor is the same whether the base goes into a three-wall alcove or a two-wall corner. There is no stock pan smaller than the 30 by 60 inch standard. Ella manufactures its own acrylic shower bases in three standard shower pan sizes: 30 by 60, 32 by 60 and 36 by 60 inches, each with a left or right drain. All three share the 60 inch length and differ only in width, so 30 inches is the narrowest stock width, there is no shorter stock length, and a space shorter than 60 inches always points to a custom base.

The encouraging part is that short and square pans are routine work. Sizes such as 46 by 46, 50 by 30 and 36 by 44 inches have all been handled as custom builds, and a 58 by 30 inch base with a center drain has been produced. A custom base is made to your length and width in the same finished acrylic as the standard pans, so it is ready to use once it is installed and does not need to be tiled over. Your contractor sets the base, connects the drain and finishes the walls around it.

One more pan family is worth knowing about. Complete multi-piece shower kits use their own pans, such as the 60 by 33 inch three-piece low-threshold kit with a molded seat, so a kit is sized as a whole unit and not pan by pan.

Small Pan Options Side by Side

OptionSizeDrain positionBest for
Custom three-wall alcove base, smallest30 by 30 inchesLeft, right or center, at least 9 inches from each wallThe most compact alcove shower Ella makes
Custom corner base, smallest30 by 30 inchesLeft, right or center, at least 9 inches from each wallA compact shower set into a two-wall corner
Custom base that has been produced58 by 30 inchesCenterAn alcove just short of the standard 60 inch length
Standard base, narrowest30 inches wide by 60 inches longLeft or right, set positionThe smallest stock pan and the narrowest 60 inch alcove
Standard base32 inches wide by 60 inches longLeft or right, set positionA slightly wider 60 inch alcove
Standard base, widest36 inches wide by 60 inches longLeft or right, set positionThe widest standard alcove
Custom three-wall alcove base, largest44 inches wide by 80 inches longLeft, right or center, at least 9 inches from each wallSpaces longer or wider than the standard sizes
Custom corner base, largest42 by 60 inchesLeft, right or center, at least 9 inches from each wallThe largest two-wall corner layout

What the table means for your bathroom is simple. If you have a 60 inch alcove, a standard pan is the easiest choice, because the drain sits in a set position for each size and you only confirm the left or right side so it lines up with the drain line already in your floor. If your space is shorter than 60 inches, or closer to a square, you are in custom territory, and the trade is a pleasant one: you give up the stock size and gain the freedom to place the drain left, right or center. Alcove and corner bases share the same 30 by 30 inch minimum and only part ways at the large end, where an alcove base can reach 44 by 80 inches and a corner base tops out at 42 by 60 inches. The minimum is the same for both, but they are not the same request, so tell your Ella dealer or the team at (800) 480-6850 which layout you have, because the drain and the finished edges are placed differently for each.

What Sets the Limit on a Small Pan

The first limit is the drain rule. On a custom base the drain can be placed left, right or center, but it must sit at least 9 inches from each wall. A drain only 7 inches from the threshold edge is not possible, even on a custom pan. On a large base that rule leaves plenty of room to work with. On the smallest pans it matters much more, because the walls are closer together and the part of the floor where the drain is allowed to sit shrinks with them. That makes it the rule to check first, because the existing drain line in your floor has to land where the rule allows it. If the center of your drain is closer than 9 inches to any wall, raise it with your Ella dealer or the team at (800) 480-6850 before your order is placed. The length, the width and the drain position are all fixed when the pan is made, so this is a detail to settle on paper and not on installation day.

The second limit is shape. Only rectangular sizes are made. Bases with angled or curved edges are not offered, so a neo-angle corner, a curved front or any other non-rectangular footprint is not a fit for an Ella base. A square 30 by 30 inch pan is fine. The first question for a tight or odd room is whether a rectangle of at least 30 by 30 inches can be drawn into it. On a custom three-wall base the threshold goes on the longer side, which is worth knowing when you sketch where the entry will be.

The third choice, not so much a limit, is the threshold. A custom shower base typically has a threshold of about 3 inches. For a barrier-free entry, zero threshold bases sit flush with the surrounding floor instead. Wheelchair accessible roll-in bases come in the three standard sizes with the drain position specified at order time, they ship with a self-adhesive collapsible rubber dam that keeps water in while a wheelchair rolls over it, and sizes outside those three can be made to order. Your Ella dealer or the team at (800) 480-6850 can confirm which threshold style suits your bathroom, what can be made if you have a different entry in mind, and how it meets your plumbing rough-in.

How to Measure a Small Space for a Pan

A small shower leaves very little room for a measuring mistake, so take these five notes before you ask for a base. The full walk-through, including the corner base rules, is in How Do You Measure a Shower Base, Including a Corner Base?.

  1. Width. Measure across the opening the base will fill.
  2. Length. Measure along the back wall. Anything under 60 inches means a custom base.
  3. Drain position. Find the existing drain line in the floor and measure from its center to each wall, then check it against the 9 inch rule.
  4. Layout. Note whether the base is enclosed by three walls or sits in a corner against two walls.
  5. Entry. Note which side is the entry and whether you want a curb-less roll-in edge, a 3 inch step-in threshold or a zero threshold flush with the floor.

If both the width and the length come out at 30 inches or more, and the space is a rectangle, share the figures with your Ella dealer or the team at (800) 480-6850 and they will confirm what can be made for your space.

Measure the finished opening, not the framing, and order the pan in that size. An Ella pan is built to size at the factory, with its length, width and drain position fixed when it is made, so the answer to a tight space is a custom order and never a saw. That point is covered in Can shower pans be cut to size or ordered custom?. Any on-site fitting happens in the walls above the pan: Ella's cultured marble travertine wall panels have factory finished edges that can be trimmed and cut for a custom fit, and Ella's acrylic wall panels come 98 inches high in a plain white finish.

The installation video on this page follows a low-threshold 3-piece shower kit, not a custom pan, but the habit it teaches applies to any small shower. It shows the installer dry assembling the unit in a clean, open space before it goes into the bathroom, to confirm that the correct panels and the correct drain location arrived and that the pan is free from damage. It also recommends delaying demolition of the existing bathtub area until you are confident the new unit is the correct size and condition, so nobody is left without a working bathroom, and checking the framing pocket against the framing diagrams for square, plumb and level. With a small pan there is very little room to adjust, so check the size and the drain location first. As the video puts it, slow is fast.

The Other End of the Range, and Small Tubs

People who search for the smallest pan often ask about the biggest one in the same breath. The largest custom base is 44 inches wide by 80 inches long, in a rectangle only, and corner bases top out at 42 by 60 inches. A 38 by 80 inch base with a left drain is within the limits, while a request such as 53 by 76 inches cannot be produced.

If the room is small enough that you are also weighing a compact tub against a compact shower, the smallest bathtub in the Ella's Bubbles line is the Mobile walk-in tub, which measures 26 inches wide by 45 inches long. The compact tub models are compared in What is the smallest bathtub size you can buy for a bathroom?. Whichever way you lean, send your five measurements to your Ella dealer or the team at (800) 480-6850, or open a ticket at ellasbubbles.com/support, and they will match the base to your space.

Video
Chapters in this video
  1. 0:00 Introduction to Low-Threshold Shower Installation This video provides visual guidance for installing a low-threshold 3-piece shower, emphasizing the importance of referring to the installation manual.
  2. 0:24 Dry Assembly and Pre-Installation Checks The installer dry assembles the modular shower to ensure correct panels, drain location, and proper alignment before moving it into the bathroom space.
  3. 1:54 Preparing the Framing Pocket and Subfloor The installer checks the framing pocket for proper sizing, square, plumb, and level, making necessary adjustments and inspecting the subfloor for integrity.
  4. 4:07 Installing the Drain Body and Base Support The installer installs the drain body, prepares the drain to meet local plumbing codes, and applies silicone adhesive for proper support and adhesion of the base.
  5. 5:53 Permanently Installing and Securing the Base The installer permanently positions and levels the shower base, securing it to all available studs and cutting the drain pipe even with the rubber gasket.
  6. 7:22 Installing the Wall Panels and Valve The installer installs the wall panels using a pin and slot system, then installs the valve, connecting the hot and cold water supply lines.
  7. 10:19 Finishing Touches and Accessories The installer caulks all seams, recommends client involvement for accessory placement, and suggests an optional flange trim molding kit for a seamless transition.

Watch: Step-by-Step Low-Threshold Shower Installation for Remodeling | Ella’s Bubbles with chapters and a full transcript.

Common Questions

What is the smallest shower pan Ella's Bubbles can make?
The smallest is a custom acrylic base measuring 30 by 30 inches. That minimum applies to both three-wall alcove bases and corner bases. Anything at that size is a custom request, because there is no stock pan that small.
Can I order a shower pan smaller than 30 by 30 inches?
The custom shower base page lists 30 by 30 inches as the minimum, and that floor applies to both three-wall alcove bases and corner bases. If your space is tighter than that, share your measurements with your Ella dealer or the team at (800) 480-6850 so they can confirm what will fit.
What is the smallest standard shower pan size?
The smallest standard pan is 30 inches wide by 60 inches long, with a left or right drain. The other two standard sizes are 32 by 60 and 36 by 60 inches. All three share the 60 inch length and differ only in width.
Is there a standard shower pan shorter than 60 inches?
No. The three standard sizes are 30 by 60, 32 by 60 and 36 by 60 inches, so all of them share the 60 inch length, and a shorter or square footprint is always a custom request. Pans shorter than 60 inches are routine custom builds, and a 58 by 30 inch base with a center drain has been produced. Sizes such as 46 by 46, 50 by 30 and 36 by 44 inches have also been handled as custom builds.
Can a standard shower pan be cut down to fit a smaller space?
Ella shower pans are built to size at the factory, and the length, width and drain position are fixed when the pan is made. The route to a fit is a custom base made to your dimensions. The part of an Ella shower that is trimmed on site is the wall surround, not the pan.
Where can the drain go on a small custom shower pan?
On a custom base the drain can be placed left, right or center. It must sit at least 9 inches from each wall, and a drain only 7 inches from the threshold edge is not possible even on a custom pan. Measure from the center of your existing drain line to each wall before you request a size.
Can a small shower pan have an angled or curved front?
No. Only rectangular bases are made, and bases with angled or curved edges are not offered. A square pan such as 30 by 30 inches is within the range, but a space that needs a non-rectangular pan is not a fit for an Ella base.
Is the smallest corner shower pan the same size as the smallest alcove pan?
Yes, both start at 30 by 30 inches. They differ at the large end, where corner bases go up to 42 by 60 inches and alcove bases go up to 44 inches wide by 80 inches long. Tell your Ella dealer or the team at (800) 480-6850 which layout you have, because the drain and the finished edges are placed differently for each.
Does a small custom shower pan need to be tiled over?
No. Ella pans, standard or custom, are finished acrylic and are ready to use once installed. Your contractor sets the base, connects the drain and finishes the walls around it.
What is the biggest shower pan you can buy from Ella's Bubbles?
The largest custom base is 44 inches wide by 80 inches long, in a rectangle only, with the threshold on the longer side. Corner bases top out at 42 by 60 inches. A 38 by 80 inch base with a left drain is within the limits, while a request such as 53 by 76 inches cannot be produced.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket