Support Center / Plumbing & Electrical / How Do I Install a Bathtub Drain Assembly on a Walk-In Tub?
Back to Plumbing & Electrical

How Do I Install a Bathtub Drain Assembly on a Walk-In Tub?

On an Ella walk-in tub you do not install the drain assembly yourself. The gravity dual drain is fitted at the factory, so the tub arrives with its drain body in place and four open ports, and your plumber's job is to connect those ports to the house drain line. If a piece of that assembly ever needs replacing, Replacing Drain Elbows, Nuts, Gaskets, Drain Covers and Plunger Parts on a Walk-In Tub explains which parts are available and how the team matches them to your tub.

What Is Already Installed When the Tub Arrives

Most instructions for installing a tub drain assume a bare tub with an empty hole in the floor and a drain kit in a box. An Ella walk-in tub is a different starting point, and a much easier one. The holes in the shell are drilled at the factory to Ella's own assembly, the drain body is mounted under the tub floor, and the parts that operate the drain are already in place when the crate is opened.

Ella walk-in tubs have dual four-port T-type drains, and stainless steel cables open and close them. Each cable runs inside a protective black plastic sleeve from the drain handle to a connection box on the drain. Inside that box the cable moves an armature, and the armature opens and closes the drain through the drain stem. All of this is assembled before the tub ships, so nobody on site has to build it.

That leaves three small jobs for installation day: connecting the open ports to the house drain line, fitting the floor drain stopper, and confirming that the handles open and close the drains cleanly. Each one is covered below.

What Your Plumber Connects

The house drain line is best built before the tub is set in position. With the line already waiting, the connection becomes a matter of joining the tub's open ports to pipe that is ready for them, instead of working in a tight space after the tub is in place.

  • Join the ports to the house drain line. The drain pipes are standard PVC, so they can be cut and rejoined with ordinary couplings.
  • Use Ella parts for the drain body and its fittings. The elbow joins the drain body to the house piping, and threaded nuts with rubber gaskets screw onto the drain tailpieces. These are tub-specific parts, so they come from Ella and are not replaced with a generic fitting.
  • Tighten snug, never forced. Any fitting should go on snug and not forced, because overtightening is what usually cracks a plastic elbow later.
  • Have a licensed plumber do the work. Ella does not send technicians. A local licensed plumber makes the connection, and parts ship from Ella when they are needed.

Fitting the Floor Drain Stopper

The floor drain stopper is the one piece of the drain you may fit by hand. It has an adjustable leg and a back nut, and it goes together in this order:

  1. Screw the back nut onto the adjustable leg.
  2. Insert the leg into the drain stopper.
  3. Tighten the back nut with pliers or a wrench until it is snug.
  4. Insert the stopper into the drain assembly.

The drop-in drain cover at the bottom of the tub simply drops back into place. It is easily lost during a plumbing visit, so it is worth checking that it is back in the drain before your plumber packs up.

Handles, Chain and Cable: The Parts That Work the Drain

Each drain handle slips onto the brass mounting on the drain assembly and is held by a single set screw that takes a 2.5mm Allen key. Before the handle goes on, the key ring at the end of the emergency pull-up chain is slipped over the brass mounting so it rests under the handle. If that step is skipped, the emergency chain has nothing to anchor to, so the ring is seated first every time a handle comes off. The full sequence is in replacing a drain handle or overflow plate.

A handle that wobbles after installation usually just needs its fasteners snugged, as described in why drain handles are loose and how to tighten them. A handle that sticks in the open position is a different symptom, and the screw stop fix for a drain lever stuck open covers it.

The video on this page shows how the cable side of the assembly comes apart and goes back together, which is the closest thing to a drain installation an Ella owner or plumber will perform. It shows the small service panel being removed from the connection box on the drain, the armature being drawn out carefully and slowly, and the barrel end of the cable being released. A drain handle is then removed with an Allen wrench, the retaining ring nut on the vent is loosened, and the drain vent assembly is taken out so the old cable can be unscrewed and the new one screwed in completely. On reassembly the video shows the locking nut tightened firmly but not over torqued, a thin bead of silicone placed on the back of the vent assembly before it goes back into the drain vent hole on the tub, and the cable barrel end seated on the armature with the flat side of the cable connection facing up. The last check is a positive connection between the drain stem and the armature before the small panel goes back on the connection box.

The video also gives the best piece of everyday advice for a new drain: stepping on an open drain puts tremendous stress on the cable and can break it, which is why a warning sticker is placed on every tub before it ships.

Why the Factory Assembly Should Stay in Place

We recommend keeping the factory drain assembly and not swapping in an aftermarket one. The holes are already drilled to Ella's assembly, and removing it creates leak risks and voids the warranty on the affected parts.

When something does wear or break, most pieces of the drain are available individually:

  • The drain elbow, which is replaced as a unit if it or its securing nut cracks. A dual drain may need one for each side.
  • The threaded nuts and rubber gaskets, which can turn brittle over time and start to weep.
  • The drop-in drain cover or plug.
  • The seat that a cable-driven plunger drops into.
  • The complete drain assembly, which the team may recommend when an internal piece is missing or broken and the cause is unclear.

Drain designs have varied across tub generations, so photos matter. Photograph the model and serial label, which is on the sticker behind the magnetic access panel next to the door or on the paper label on the side of the shell. Photograph the drain from above the tub floor and, if your plumber has the apron off, the drain body and elbow underneath. Then open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your model number, where you purchased the tub and the shipping address for the part. The team can also supply the drawings for your model. Ella ships the part, and a local licensed plumber fits it.

Video

Watch: Drain Cable Replacement with chapters and a full transcript.

Video
Video

Common Questions

Do I have to install the drain assembly on an Ella walk-in tub myself?
No. The gravity dual drain is fitted at the factory, and the tub arrives with its drain body in place and four open ports. Your plumber connects those ports to the house drain line.
Should the house drain line be built before the tub is set?
Yes, that is the best order. The house drain line is best built before the tub is set in position, so the open ports on the drain body can be joined to pipe that is already waiting.
How tight should the drain fittings and elbows be?
Every fitting should go on snug and not forced. Overtightening is what usually cracks a plastic elbow later, so firm hand pressure and a careful final turn are the goal.
How does the floor drain stopper go together?
Screw the back nut onto the adjustable leg, then insert the leg into the drain stopper. Tighten the back nut with pliers or a wrench until it is snug, and insert the stopper into the drain assembly.
Can I swap the factory drain for an aftermarket drain assembly?
We recommend keeping the factory assembly. The holes in the tub are drilled to Ella's assembly, and removing it creates leak risks and voids the warranty on the affected parts. Replacement parts for the factory drain are available through ellasbubbles.com/support or (800) 480-6850.
Who installs a replacement drain part if one is needed?
Ella ships the part and does not send a technician. A local licensed plumber does the labor, and the team can provide the drawings for your model when you call (800) 480-6850 with your model number.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket