Support Center / Maintenance & Cleaning / How do I clean the faucet cartridge on a walk-in bathtub?
Back to Maintenance & Cleaning

How do I clean the faucet cartridge on a walk-in bathtub?

To clean a faucet cartridge on an Ella walk-in tub, shut off the hot and cold supply, remove the handle, the escutcheon and the locking collar, lift the cartridge out, clean off the calcium and debris with a soft brush, rinse, and reassemble without over torquing. The cartridge that most often needs this is the one inside the thermostatic control valve, and Why Does Hard Water Keep Ruining My Temperature Valve? explains why scale collects there. This page is the how-to for each Ella cartridge type, with what to clean, what to check on the way back in, and what to do if cleaning does not solve it.

Before You Start: Which Cartridge Is It, and Does It Need Cleaning?

An Ella tub can have more than one kind of cartridge, and your order tells you which faucet package was built into your tub.

  • The thermostatic control valve, or TCV. Tubs with an Ella thermostatic faucet package have a TCV that blends hot and cold to a set temperature. Its cartridge and intake screens are where calcium, iron and fine particles settle.
  • The 5-piece fast-fill faucet. This faucet mixes with separate manual hot and cold handles and is not thermostatic. Each handle sits on its own cartridge.
  • The two-piece faucet. The cartridge sits under the spout handle, held by a brass locking collar.

The signs that point to a fouled TCV cartridge are consistent across Ella's troubleshooting guides. The water runs well above the temperature you set, as described in Why Is the Water in My Walk-In Tub Too Hot? The water comes out only scalding or only cold with nothing in between. The valve starts to stick. Or hot and cold cross over inside the tub's plumbing when the tub is off, so the rest of the home loses hot water until the tub's shut off valves are closed.

Ella's guides have a licensed and insured plumber do this work. The procedure is short, and the videos on this page show it clearly enough to hand to whoever does the job.

Cleaning the Thermostatic Control Valve Cartridge

  1. Shut off the hot and cold supply to the tub at the shut off valves.
  2. Remove the control handle and the cover plate.
  3. Remove the washers and the escutcheon plate, then unscrew the metal collar.
  4. Unscrew and lift out the cartridge.
  5. Clean the cartridge and the intake screens of calcification with a soft brush and a lime scale remover such as CLR. The screen and the check valve at the bottom of the valve also collect sediment and calcification, and they are easy to clean while the cartridge is out.
  6. Lightly lubricate the gaskets with lithium grease.
  7. Reassemble in reverse order, tightening the collar securely without over torquing.
  8. Open both shut off valves fully and test the valve on both hot and cold settings, confirming that the fill temperature responds normally.

If you would like to see the retrieval step before starting, the support team can send a video that shows how to remove the TCV cartridge and clean it.

The Handle Cartridges on the 5-Piece and Two-Piece Faucets

The two videos on this page show how these cartridges come out and go back in.

5-piece faucet. The video shows the full sequence on one handle. Remove the red or blue cap on the handle, loosen the bolt underneath with an Allen wrench, and lift off the handle. Remove the plastic collar under the handle, then loosen and remove the cartridge with a socket wrench. Check the cartridge for debris, foreign objects or calcification, and if needed clean it with a soft brush and then rinse. Replace the cartridge and tighten it without over torquing, refit the plastic collar, put the handle back on facing the correct position, tighten the Allen bolt firmly, and replace the colored cap. The video names the exact tool sizes.

Two-piece faucet. The video shows a cartridge replacement, and the same steps get the cartridge out for inspection. Remove the decorative bolt cover, loosen the Allen bolt and lift off the spout handle. Unscrew and remove the escutcheon plate, loosen and remove the brass locking collar, and simply lift out the cartridge. Going back in, the two guide posts on the cartridge must line up with the receptacles in the spout housing, because the cartridge only seats correctly when both posts are in position. Tighten the brass collar securely without over torquing, hand tighten the escutcheon plate, refit the handle and the bolt cover. The red side should be on the left for hot and the blue on the right for cold.

Keeping the Cartridge Clean Afterward

Fouling comes from the water supply, so a clean cartridge will foul again unless the supply is filtered. The TCV must be protected by an inline filter or mesh on the water lines, and that filter has to be cleaned periodically. Without one, the same scale returns no matter how many times the cartridge or the knob is replaced.

  • If no filter or mesh is fitted, have a licensed, insured plumber add one before anything else is replaced.
  • If a filter is fitted, remove and clean it, then note how quickly it loads up again. That tells you how often it needs attention in your water.
  • Very hard or iron rich water needs the screens cleaned more often than usual.

The monthly vinegar flush is a different job. Mixing 2 cups of white vinegar with 2 cups of water, filling to 1 inch above the highest jets, adding the mixture, running the tub for 10 minutes and draining cleans the jet lines. It does not clean the faucet cartridge, which sits on the supply side.

When Cleaning Is Not Enough

Work through the next steps in order.

  1. Replace the cartridge. If the water still will not mix, the valve still overshoots, or a crossover continues after cleaning, a new cartridge is the next step. For a crossover, first rule out the hand shower's check valve and hose orientation, as covered in Why Does the Mixing Valve Cross Hot and Cold When the Tub Is Off?
  2. Check the cold inlet. If the tub delivers only hot water wherever the dial is set, the cold line has pressure and the inlet screen is clean, the cause is likely the check valve at the cold inlet rather than the cartridge. Cold Water Reaches the Tub but Will Not Come Out of the Faucet: Unlocking the TCV Check Valve walks through freeing it.
  3. Replace the valve. If the valve itself has failed, replacing the whole TCV is the recommended repair.
  4. Consider a manual faucet. Where cleaning becomes a recurring chore, tech support may suggest the Ella 5-piece fast-fill faucet, which has no thermostatic cartridge to foul. It does not hold a set temperature on its own, a point explained in Tub Fills Only Scalding or Only Cold and Will Not Mix to Warm.

On coverage, the TCV carries a 1-year limited warranty and is not part of the lifetime parts warranty. Cartridge fouling from calcium, iron or contaminated water is not a covered defect. When a part is covered, it ships under the warranty and a local licensed plumber does the labor. To ask about parts or about Ella's cartridge cleaning service, contact your Ella dealer or the team at (800) 480-6850, or open a request at ellasbubbles.com/support with your model and serial number, a photo of the faucet set, and a note on whether a filter is fitted.

Video
Watch: Ella's Bubbles: Cartridge Replacement 5 Piece with chapters and a full transcript.
Video

Watch: Ellas Bubbles: Two Piece Faucet Cartridge Replacement with chapters and a full transcript.

Video

Common Questions

What should I use to clean a faucet cartridge?
Use a soft brush, and for the thermostatic control valve cartridge and its intake screens, a lime scale remover such as CLR. Rinse the parts before reassembly. Lightly lubricate the gaskets with lithium grease as the valve goes back together.
Do I need to shut off the water before removing the cartridge?
Yes. Shut off both the hot and cold supply to the tub at the shut off valves before the handle comes off. Open both valves fully again once the faucet is reassembled, then test it.
How often should the thermostatic valve cartridge be cleaned?
Ella's guides give no fixed interval, because it depends on your water. Clean the inline filter, note how quickly it loads up again, and use that as your guide. Very hard or iron rich water needs the screens cleaned more often than usual.
Why does my cartridge foul again soon after cleaning?
Scale is reaching the valve from the supply. The TCV must be protected by an inline filter or mesh that is cleaned periodically. Without one, the same fouling returns no matter how many times the cartridge or the knob is replaced.
Is a fouled faucet cartridge covered by the Ella warranty?
The TCV carries a 1-year limited warranty and is not part of the lifetime parts warranty. Cartridge fouling caused by calcium, iron or contaminated water is not a covered defect. When a part is covered, it ships under the warranty and a local licensed plumber does the labor.
Does the monthly vinegar flush clean the faucet cartridge too?
No. The vinegar flush runs through the jet lines, not the water supply side where the cartridge sits. The cartridge is cleaned by removing it, and it is protected by an inline filter or mesh on the supply lines.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket