Support Center / Showers, Panels & Accessories / How Do You Fit a Folding Shower Screen on a Walk-In Tub?
Back to Showers, Panels & Accessories

How Do You Fit a Folding Shower Screen on a Walk-In Tub?

A folding shower screen is fitted to the wall beside your walk-in tub, never to the tub itself. Its wall channel is set level, at a height where the rubber gasket along the bottom brushes the tub deck lightly and evenly. Getting the wall, the starting end and that gasket height right is most of the job. The screen itself is described in What Is the 4-Fold Shower Screen on a Walk-In Tub?, and this page takes you through the fitting decisions in the order you will meet them. The printed installation manual that comes with the screen remains the step list to follow for fasteners and parts.

Before You Start: Confirm the Screen and the Layout

Ella makes two glass screens, and both are alcove screens designed for a tub whose back and both ends sit against finished walls. Check that you have the right one for your tub before any hole is drilled.

  • Every seated walk-in tub takes the 4-fold tempered glass screen, which is 44 inches wide by 42 inches high in a chrome finish.
  • The LayDown tubs, the Ella models without a seat, take their own bi-fold screen. It uses its own mounting positions and hardware with an installation diagram, and it will not fit a seated model.
  • A seated 52 inch tub in a 60 inch alcove with an extension panel uses the same 4-fold screen with one section removed, which makes a 32 inch wide 3-fold screen.

If you are unsure which situation is yours, Which shower screen or curtain fits your Ella walk-in tub model? maps each tub type to its screen. A plain shower curtain is the answer whenever the tub does not sit in a full three-wall alcove.

Also check coverage against your tub length before you mount anything. One size of 4-fold screen has to fit every seated Ella tub, which is why it is 44 inches and not the full length of the tub. On a tub whose top measures about 59 to 60 inches, the screen leaves roughly 15 inches uncovered at one end. Panels cannot be added later, because current screens are built as a more rigid unit limited to four panels. This check matters for a second reason: a screen follows the standard 30-day return policy for uninstalled products in original packaging, so once it is mounted it can no longer be returned. The details are in Four-Fold Glass Shower Screen: Damaged Hardware, the Return Window and Why Panels Cannot Be Added.

Shower screens ship in several pieces and are assembled on site. Look over the hardware as you unpack it. If a piece is damaged or a panel will not slide, photograph the damage and the packaging, and open a ticket before going further.

Choose the Wall and the Starting End

The screen mounts to the side wall, ideally into a stud. It is reversible for a left or right installation, so the same screen works whichever end of the alcove you choose. Three rules decide where it goes:

  • Mount it on the wall side away from any extension panel.
  • Start it at the back wall at the seat end and run it toward the grab bar at the front, crossing the door. This way it covers the entire seating area, where most showering happens.
  • Starting at the standing end may not be possible, because the grab bar can be in the way.

The screen has a knob on both sides, folds accordion style against the wall and pivots 90 degrees at the wall channel for entry, so make sure nothing on that wall blocks the fold or the pivot. If your tub has a swivel tray, plan the two together. The tray rotates out of the way for entry and exit, so position the screen so the tray can swing clear. What Are My Options If My Swivel Tray Broke or Does Not Fit? explains how the tray mounts near the door.

Convert It to a 3-Fold First, If Your Alcove Needs It

If you need the 32 inch 3-fold version, do the conversion before the screen goes on the wall. The assembly video shows the whole process on a four panel door:

  1. Lay the four panel door carefully down on a soft surface.
  2. Elevate the third panel from the wall side and remove the inside screw. Do the same on the other side, removing the outside screw.
  3. Use any long screw you have to remove the plastic retainer insert. This releases the panel connection. Do the same on the other side.
  4. Go to the other side of the door and repeat the same process: remove the screw on the third panel, then both plastic retainer inserts. The third panel is now free and can be removed completely.
  5. Bring in the outside panel to connect with the middle panel, keeping the plastic spacer in place, and reconnect the hinge.
  6. Replace the plastic retainer insert and secure it with the same screw. Tighten securely but do not over torque. Repeat for all connections.
  7. Snap the screw caps onto the top side of the door. It is now ready for installation.

Set the Wall Channel Height and Level

This is the step that decides whether the screen stays dry. Along the bottom of the screen runs an inward-angled rubber gasket, and that gasket is the seal. It should brush the tub deck lightly and evenly along its whole length.

  • Set too low, the gasket gets damaged.
  • Set too high, water escapes underneath.
  • If the channel is out of level, the gasket cannot touch the deck evenly, so check level as well as height.
  • Confirm the gasket is angled inward toward the tub.

Fold and unfold the screen and swing it through its 90 degree pivot while you check the gasket, so you see how it meets the deck along the full run and not only at the wall.

Trim the Horizontal Seal with Care and Fit the End Cap

The horizontal seal runs along the bottom of the screen and rides on the tub deck to keep spray inside the tub. Installers cut this seal to length, and it is the one cut that is easy to get wrong. If the seal is cut short, there may not be enough left to protect the tub deck under the end cap, and a new cap will not fix a wet deck on its own. Leave enough seal beyond the last screen panel before you cut.

The end cap fits onto the end of the horizontal seal, holds it in place and covers the cut edge. The printed installation manual covers attaching it in steps 4 and 5. Let any sealant the manual calls for cure before the next shower. If a cap comes loose later, Replacing or Reattaching the End Cap and Horizontal Seal on a Folding Shower Screen covers refitting it.

Check Your Work and Look After the Screen

If water shows up at the bottom of the screen after the first shower, level the screen, set the height so the gasket seats on the deck, and confirm the gasket is angled inward toward the tub. Clean the glass with warm soapy water and a lint-free cloth after use. Never use alcohol, petroleum liquids or chemical cleaners on the screen, and never anything gritty.

If something does not line up, contact your Ella dealer or the team at (800) 480-6850, or open a request at ellasbubbles.com/support. Have your tub model and serial number, whether the screen is set up as 4-fold or 3-fold, and a photo of the gasket and of where the water appears.

Video

Watch: Ella's Bubbles: Three Fold Shower Screen Assembly with chapters and a full transcript.

Video

Common Questions

Does the folding shower screen attach to the tub or the wall?
It attaches to the wall, ideally into a stud, and never to the tub. A rubber seal along its bottom edge rests on the tub deck to keep water inside.
Which end of the tub should the folding screen start from?
The screen normally starts at the back wall at the seat end and runs toward the grab bar at the front, crossing the door. That covers the entire seating area, where most showering happens. Starting it at the standing end may not be possible because the grab bar can be in the way.
How high should the folding shower screen be set above the deck?
Set it so the inward-angled rubber gasket brushes the tub deck lightly and evenly. If it is set too low the gasket gets damaged, and if it is set too high water escapes underneath. The sources give this as a fit to check by eye, not a measured height.
Can I add a folding screen after my tub is installed?
Yes. The screen is an accessory that mounts to the wall beside any Ella walk-in tub that sits in a corner or alcove, and it can be added after the tub is installed.
Can the 4-fold shower screen be made narrower for my alcove?
Yes. Removing one section converts it to a 32 inch wide 3-fold screen. This is the setup used in a 60 inch alcove where a 52 inch tub has an extension panel, and the assembly video shows the conversion.
Can I return a folding screen after it has been mounted?
No. The screen follows the standard 30-day return policy for uninstalled products in original packaging, and a return must be authorized before anything is shipped back. Check its coverage against your tub length before you install it.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket