Support Center / Showers, Panels & Accessories / Can You Use PVC Wall Panels Inside a Shower Enclosure?
Back to Showers, Panels & Accessories

Can You Use PVC Wall Panels Inside a Shower Enclosure?

Yes. Ella's grout-free tongue and groove PVC wall tiles are made for exactly that, as a way to upgrade a shower or bath enclosure over new or existing surfaces. They belong in a wet area on three conditions: the wall behind them is an approved substrate, the material acclimates in the bathroom first, and every seam is sealed with silicone. The full method is in How do you install and seal tongue and groove PVC shower wall tiles?, and this page explains what makes a PVC wall work inside a shower and what to check before you commit to it.

What the Ella PVC Wall Product Is

The PVC tile is one of the four wall families Ella offers for the space above a walk-in tub or around a shower base. The other three are the acrylic 3-panel kit, the SMC subway-pattern panel kits and cultured marble panels. The PVC product is a grout-free interlocking tile. A tongue on one edge fits into a groove on the next tile, so the wall goes together snugly and securely without grout lines to seal or scrub.

The installation video on this page shows the tiles in a Carrara marble look and describes them as a simple, stylish way to upgrade a shower or bath enclosure. In the video the tiles are measured, scored and snapped to size, adhesive is applied to the back, a thin bead of silicone is placed at each joint for a watertight seal, and each tile is set and then snapped into place.

One caution on names. The SMC subway kits also use a tongue and groove interlock, and they are a different product. SMC panels are a pressed fiberglass composite that goes up in 24 inch rows on 100 percent silicone, with an overlapping flange on each panel. The PVC tiles are individual pieces that are cut, glued and snapped together. When you ask a question about your wall, say which one you have.

Why a PVC Wall Holds Up to Shower Water

A glue-up wall keeps water out in a different way than ceramic tile does. Traditional tile is built up one piece at a time on a prepared substrate, with grout joints between every tile and a joint at the base that must be properly sealed. Ella's wall options arrive with the surface already sealed, so the places water can get in come down to the joints and edges, and each of those is sealed with silicone rather than grout.

On the PVC tiles the joint is a tongue in a groove, and the interlock alone is not the seal. In a wet area every seam gets silicone. That is the detail that turns a PVC wall into a shower wall, and it is why the video shows a bead of silicone at each joint before the tile is snapped in. How do I seal shower wall panels to keep water out? maps the sealing points on each of Ella's wall families.

The Conditions That Make It Work

  1. Let the tile acclimate. Bring the cartons into the bathroom and leave them for 24 hours before installation so the material settles to the room's temperature and humidity. A tile that is cut and snapped in on the day it arrives can move as it adjusts, and the joints are where that shows.
  2. Start with an approved substrate. The tiles are glued, so the wall behind them has to be sound, clean and dry. They can go over a new or an existing surface, as long as that surface qualifies as an approved substrate. A panel should never be installed over a damaged wall, and a completely waterproof substrate is recommended in a wet area.
  3. Measure and plan the cuts. Measure each wall at the top, middle and bottom before you cut. Hold back about 10 percent spare tile for cuts.
  4. Glue, seal, set and snap. Apply adhesive to the back of the tile, run a thin bead of silicone at the joint, then set the tile and snap it into the one before it.
  5. Seal the edges too. The line where the wall meets the tub deck or shower base takes water every time the shower runs, so it is sealed with silicone. A factory edge is finished, but an edge you cut around a valve, a window or a niche is not, until you seal it or cover it with trim.

Checking the Wall Behind the Tile

Because a glued wall makes the surface behind it part of the system, the substrate deserves a careful look before the first tile goes up. The substrates named for an Ella wall kit are moisture-resistant drywall, marine-grade plywood or cement board, sealed with a water-based or oil-based primer and sealer. Plaster, concrete, or a wall that has just had wallpaper removed takes two coats. The reasoning and the product types are covered in What primer or sealer goes on drywall before acrylic shower walls?.

An unsealed spot behind a panel is where water can get in if a seam ever opens, which is why the preparation matters as much as the silicone. If you are unsure whether your existing wall qualifies for the PVC tiles, describe it to the team at (800) 480-6850 before you start rather than after. Local building codes for shower and tub enclosures still govern the job, so your contractor should confirm the wall build-up for your area.

Is PVC the Right Wall for Your Shower?

The PVC tile suits a project where you want a tile look without grout and want to build the wall one manageable piece at a time, cutting each piece by scoring and snapping it. Because the tiles go on individually, there are more joints than on a large-panel wall, and each one needs its bead of silicone. Take your time at the seams and the wall will reward you.

If you would rather have fewer seams, the acrylic route covers the enclosure with a small number of large panels. What Is an Acrylic Shower, and How Does It Compare to Tile? describes those panels and how they compare with a tiled wall. Your Ella dealer or the team at (800) 480-6850 can help you match a wall family to your tub or shower base, and you can also reach the team at ellasbubbles.com/support.

Video

Watch: Ella's Bubbles: Grout-less Tongue & Groove PVC Carrara Tile Installation with chapters and a full transcript.

Common Questions

Are Ella PVC wall tiles made for use in a shower?
Yes. Ella's grout-free tongue and groove PVC tiles are presented as a way to upgrade a shower or bath enclosure, and they are one of the four wall families Ella offers for the space above a walk-in tub or around a shower base. In a wet area every seam is sealed with silicone.
Do PVC shower wall tiles need grout between them?
No. The tiles are grout-free and join with a tongue and groove connection, so there are no grout lines to seal or scrub. A thin bead of silicone at each joint provides the watertight seal instead.
Can PVC wall tiles go over an existing shower wall?
They can be placed over new or existing surfaces, provided the surface qualifies as an approved substrate and is sound, clean and dry. A panel should never be installed over a damaged wall. If you are unsure about your wall, describe it to the team at (800) 480-6850 before you start.
How long should PVC tiles sit in the bathroom before installation?
Leave the cartons in the bathroom for 24 hours before installation. This lets the material settle to the room's temperature and humidity. A tile installed on the day it arrives can move as it adjusts, and that movement shows at the joints.
Where does the silicone go on a PVC shower wall?
Silicone goes at every joint between tiles, along the edge where the wall meets the tub deck or shower base, and on any edge you cut on site. A factory edge is finished, but a cut edge around a valve, window or niche needs to be sealed or covered with trim.
Are the PVC tiles the same as the SMC subway panels?
No. Both use a tongue and groove interlock, but they are different products. SMC panels are a pressed fiberglass composite that goes up in 24 inch rows on 100 percent silicone, while the PVC tiles are individual pieces that are cut, glued and snapped together.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket