Support Center / Showers, Panels & Accessories / How Do I Finish the Inside Corners of Ella Acrylic Shower Wall Panels?
Back to Showers, Panels & Accessories

How Do I Finish the Inside Corners of Ella Acrylic Shower Wall Panels?

On the Ella acrylic 3-panel shower wall kit, the panels are cut to fit and the inside corners are finished with molding, which is not included, or with caulk, and every joint in the wet area is sealed with 100 percent silicone once the panels have been braced or taped for 24 hours. For a more finished look, a 1 inch corner trim in 96 inch lengths suits inside corners and the ceiling line. The wall preparation that makes a corner seal well is covered in What primer or sealer goes on drywall before acrylic shower walls?, and this page stays on the corner itself for each Ella wall system.

First, Confirm Which Ella Wall System You Have

Ella offers more than one wall system, and each one makes its inside corner differently. The corner finish that is right for an acrylic 3-panel kit is not the one used on an acrylic wall liner or an SMC subway kit, so identify your kit before you buy trim or caulk.

Wall systemHow the inside corner is formedHow the corner is finished
Acrylic 3-panel kitPanels are cut to fit, glued, then braced or taped for 24 hoursMolding (not included) or caulk, with 100 percent silicone on every wet-area joint. Optional 1 inch corner trim in 96 inch lengths
Acrylic wall liner (the 98 1/2 inch wall system)Corner reinforcements are set into the two corners before the wall panels go in, so the corners are squareColor matched silicone from the liner installation kit on every wet-area seam
SMC subway 12-piece kitThe side panel overlaps the flange of the back panel, so the corner is built inWhite caulk at the inside corners once all four rows are up
Cultured marble surroundEdges are factory finished for seamless panel joining and can be trimmed for a custom fitCorner finish not listed

The table shows the two different jobs. On the 3-panel kit and the wall liner, the corner is a joint you finish after or around the panels, so your trim or silicone work is what the eye sees. On the SMC subway kit the overlap does the structural work, and the caulk is the last cosmetic and sealing step. If you are not sure which system you have, your Ella dealer or the team at (800) 480-6850 can tell you from your order.

The Corner Sequence on the Acrylic 3-Panel Kit

The acrylic 3-panel kit is glued only. It is not screwed or nailed, so the order of work at the corners follows the adhesive.

  1. Dry-fit the panels first and cut them to fit the alcove.
  2. Set the panels and brace or tape them for 24 hours while the silicone cures.
  3. After that 24 hours, seal every joint in the wet area with 100 percent silicone. That includes both inside corners.
  4. Finish the edges with molding, which is not included in the kit, or with caulk.

Waiting the full 24 hours before the final corner bead matters, because the panels are still settling onto the wall while the adhesive cures. A bead run into a corner that is still held by braces or tape can be disturbed when the bracing comes off.

Corner Trim and Corner Tape: Two Optional Upgrades

Two accessories go beyond a plain caulked corner, and they do different things.

  • 1 inch corner trim. This trim comes in 96 inch lengths and suits inside corners and the ceiling line. It is the choice when you want the corner to read as a clean, finished line and not a caulk joint.
  • DURABASE waterproof corner tape kit. This kit is offered for 3-piece acrylic walls. It reinforces the wall-to-wall and wall-to-floor joints, which is where leaks usually start.

Because molding is not included with the 3-panel kit, decide on the corner finish when you order the walls, so the trim arrives with them. Your Ella dealer or the team at (800) 480-6850 can confirm which trim and tape suit your kit size.

Get the Corner Itself Right Before the Panels Go Up

A neat corner bead starts with the wall behind it. The walls need to be plumb and square within 1/8 inch, and the panels should go up with the room above 65 degrees. The surface has to be sound, clean, dry and sealed, because an unsealed spot is where water can get behind a panel if a seam ever opens. A panel must never be installed over a damaged wall.

The SMC installation steps make the same point: the back-to-side corner has to be plumb and square before the bottom row is dry-fitted. On that kit the panels are set on a continuous perimeter bead of 100 percent silicone with vertical beads every 8 to 12 inches. The side panel overlaps the back panel flange row by row, and the white caulk goes into the inside corners only after all four rows are up.

Acrylic Wall Liners Use Corner Reinforcements Instead

If your walls are the acrylic wall liner, the corner is handled before the panels, not after. Corner reinforcements go into the two corners first so the corners are square, the wall panels follow, and every seam in the wet area is sealed with the color matched silicone that ships in the liner installation kit. The trim pieces are listed with the shower accessories and are not described as part of the liner package, so count your inside corners before you order. The full order of work is in How Do I Install Acrylic Trim Pieces With Ella Acrylic Wall Liners?

Where the Corner Meets the Tub or the Shower Base

The bottom of each inside corner is the spot that sees the most water. Around a walk-in tub, the wall finish should come down over the tile flange, and a bead of 100 percent silicone belongs at every joint: tub to wall along all three sides and at each corner. If water shows at the corners once the tub is in use, the checks in Why Does My Tub Leak at the Corners or Wall When Filled? walk through it in order. If you are still choosing a base to go under the walls, Shower Bases and Walls: Roll-In, Seat, Custom Sizes, Thresholds and Wall Systems sets out the options.

Common Questions

Is corner molding included with the acrylic 3-panel kit?
No. On the acrylic 3-panel kit the edges are finished with molding, which is not included, or with caulk. A 1 inch corner trim in 96 inch lengths is available for inside corners and the ceiling line.
What caulk should be used on the inside corners?
On the acrylic 3-panel kit, every joint in the wet area is sealed with 100 percent silicone. The acrylic wall liner uses the color matched silicone that ships in its installation kit, and the SMC subway kit corners are finished with white caulk.
How long should I wait before sealing the corners?
On the acrylic 3-panel kit, the panels are braced or taped for 24 hours first. Once that time has passed, seal every joint in the wet area with 100 percent silicone.
What does the DURABASE waterproof corner tape kit do?
It is offered for 3-piece acrylic walls. It reinforces the wall-to-wall and wall-to-floor joints, which is where leaks usually start.
Do the SMC subway wall panels need corner trim?
On the SMC subway 12-piece kit, the side panel overlaps the flange of the back panel, so the corner is built in. The inside corners are finished with white caulk once all four rows are up.
How square do the walls need to be at the corners?
The walls need to be plumb and square within 1/8 inch before the panels go up. On the SMC kit, the back-to-side corner is checked for plumb and square before the bottom row is dry-fitted.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket