Support Center / Sizes, Fit & Measuring / What If My Alcove Is Wider Than 60 Inches for an Ella Tub?
Back to Sizes, Fit & Measuring

What If My Alcove Is Wider Than 60 Inches for an Ella Tub?

If your alcove is wider than 60 inches, the extension panel that ships with an Ella tub shorter than 60 inches may not reach the wall on its own, because that panel is sized for a standard 60 inch alcove. Your Ella dealer or the team at (800) 480-6850 can arrange a panel for the gap you measure, and any space beyond what a panel covers is framed in and finished by your installer. The general guide is Getting an Extension Panel When Your Alcove Is Wider Than Your Tub, and this page looks at the wider than 60 inches case on its own.

Why 60 Inches Is the Size Everything Is Built Around

A standard tub alcove is 60 inches, and Ella plans its extension panels around that opening. An extension panel, also called a filler kit, is an L-shaped acrylic panel that mounts on the end of the tub and extends the finished apron to the wall. It is a finish piece, not a structural part. The tub still rests on its own frame, and your installer levels and supports it exactly as usual.

Tubs shorter than 60 inches ship with one extension panel in the crate so they can drop into that standard opening. The panel takes a 52 or 55 inch tub to a 60 inch alcove. Two examples from the published guides show the idea:

  • The Ella Standard is a 30 by 52 walk-in tub that comes with an end panel for the faucet side and a 7 inch extension panel for the other side, so it fits snugly into a 60 inch alcove.
  • The Deluxe includes an 8 inch L-shaped panel that can be installed on either the left or the right end.

That is the reason a wider alcove needs a little extra planning. The panel in your crate was sized to finish a 60 inch opening, so in a wider alcove there is space left over after the panel is in place. It is a common situation with a tidy answer, and it is easiest to sort out before installation day.

If Your Tub Is Shorter Than 60 Inches

A single panel covers a gap up to its own width. When your alcove leaves more space than that, these are the routes the guides describe:

  1. Ask for a panel matched to your gap. If your gap is wider than the panel supplied, your Ella dealer or the team at (800) 480-6850 can arrange one. Have your model, your serial number and the measured gap ready when you call.
  2. Ask about a second panel on the opposite end. In some layouts a second panel can be installed on the other end of the tub, which adds roughly one more panel width. The panel mounts on stainless steel shelf brackets built into the frame, and a tub is normally built with brackets at one end only, left or right as specified on your order. On a Capri or Elite, brackets can be fitted to both ends only when that is requested before the tub is built, so raise it early if you already know your alcove is wide.
  3. Have your installer frame the rest. If the gap is wider than the panel covers, your installer frames and finishes the remaining space. The panel still gives the visible end of the tub its factory-matched look, and the framed section closes the distance to the wall.

Keep in mind which end the gap falls on. The extension panel mounts on the end away from the faucet deck, so a gap that lands on the faucet end needs a layout review. Why the extension panel does not attach on the faucet side explains how to check your order paperwork and the brackets on your frame.

If Your Tub Is a 60 Inch Model

Full-length models such as the Zen60 and Standard60 do not offer an extension panel. They are built to fill a standard 60 inch alcove, so no panel ships in the crate, even if a third-party listing suggested one was included. For those tubs in a wider alcove, your installer can frame in the extra space for a clean, finished look.

Several other models also fill their space without an extension panel: the Front Entry, Mobile, Ultimate, Big4One, Shak, Transfer60 and the two seat models. If you own one of these and your alcove is wider than the tub, the same approach applies, and the extra space is framed and finished on site.

Check the actual length of your tub before you plan the framing. The size in a model name is a nominal figure, and the spec drawing carries the real one. The LayDown 30 by 60 is sold as a 60 inch tub and has an overall length of 59 3/4 inches, and a tub described as a 5 foot tub can measure 59.5 inches long. How Wide Is a Walk-In Tub, and Will It Fit Your Home? explains which figure on the drawing is the width and which is the length.

How to Measure a Wider Alcove Before You Call

A clear measurement lets the right panel ship the first time and lets your installer plan any framing in advance.

  1. Measure the alcove wall to wall where the tub will sit, allowing for tile and drywall thickness on the finished walls.
  2. Subtract the actual length of your tub from the spec sheet, not the nominal size. The result is the gap you need to close.
  3. Note which end of the tub faces the gap, and whether that is the faucet end.
  4. Look at both ends of the frame for the adjustable shelf brackets, so you know which end is ready for a panel.
  5. Write down your model and serial number.

If your alcove is out of square as well as wide, that is fine. Extension panels are designed to be trimmed on site, so your installer can cut the panel for a seamless fit against an uneven wall. If the open end of the tub does not meet a wall at all, the piece you need is the reversible end panel instead. One is included with the tub, and a second is available through where you purchased.

What a Wider Gap Changes for the Shower Column

A wide alcove can also move the tub farther from the wall, and that matters if you are adding the overhead shower. The shower column is braced to the bathroom wall with connector rods, and the kit now ships with two rods, one adjustable from 2 to 3 inches and one from 3 to 4 inches. If the distance between your tub and the wall where the column will be braced is wider than 4 inches, for example in an alcove installation with an extension panel, contact your Ella dealer or the team at (800) 480-6850 before your installer arrives. The longer rods are no longer a standard part, so this is worth settling while the tub can still be repositioned. What Is the Shower Column Kit on a Walk-In Tub? covers the rods in detail.

What the Videos Show

The first video on this page introduces the extension panels, or filler kits. It shows that a panel can be placed on the right side or the left side of the tub, that it can be trimmed when an alcove is out of square or an unusual size, and that the stainless steel shelf support brackets are fully adjustable and an integrated part of the tub frame. It also points out a pleasant bonus: the finished panel becomes a handy place for towels, shampoos, soaps and other bathing items.

The second video walks through the Ella Standard, a 30 by 52 tub, and shows the end panel on the faucet side and the 7 inch extension panel mounted on the other side for a snug fit in a 60 inch alcove. Seeing that standard layout makes it easy to picture how much space is left over in your own, wider alcove.

Watch: Ella's Bubbles: Installation Tips For The Ella Standard Walk-In Tub with chapters and a full transcript.

Common Questions

Does the extension panel in my crate fit an alcove wider than 60 inches?
The panel included with tubs shorter than 60 inches is sized for a standard 60 inch alcove. A single panel covers a gap up to its own width, so a wider alcove leaves some space beyond it. Your Ella dealer or the team at (800) 480-6850 can arrange a panel for the gap you measure, and your installer frames and finishes any space that remains.
Can I get an extension panel for a Zen60 or Standard60?
No. Full-length models such as the Zen60 and Standard60 do not offer an extension panel, because they are built to fill a standard 60 inch alcove. When the alcove is wider, your installer can frame in the extra space for a clean, finished look.
Can a second extension panel go on the other end of the tub?
In some layouts, yes, and it adds roughly one more panel width. The panel needs shelf brackets on that end of the frame, and on a Capri or Elite brackets can be fitted to both ends only when that is requested before the tub is built. Your Ella dealer or the team at (800) 480-6850 can confirm what was built and what can be added.
What should I have ready when I call about a wide alcove?
Have your model, your serial number and the measured gap in inches. Measure the alcove wall to wall with the finished wall thickness allowed for, then subtract the actual tub length shown on the spec sheet. It also helps to note which end of the tub faces the gap.
Can the extension panel be trimmed if my alcove is out of square?
Yes. The extension panel is designed to be cut, so it can be trimmed on site when an alcove is out of square or an unusual size. Your installer does the trimming during the installation so the tub fits seamlessly.
Will a wider alcove affect my shower column kit?
It can. The shower column kit ships with two wall connector rods, one adjustable from 2 to 3 inches and one from 3 to 4 inches. If the tub will sit more than 4 inches from the wall where the column is braced, contact your Ella dealer or the team at (800) 480-6850 before your installer arrives.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket