Support Center / Walk-In Tub Models / What Is a Fiberglass Tub and How Long Does It Last?
Back to Walk-In Tub Models

What Is a Fiberglass Tub and How Long Does It Last?

A fiberglass tub is a bathtub whose body is built up in layers of fiberglass and resin, with a thin gel coat as the surface you see and touch. How long one lasts comes down to that surface layer, because the gel coat is the part that chips, cracks and dulls, and no single number of years is published for it. Ella walk-in tubs are built the other way around: a solid acrylic sheet is the bathing surface and fiberglass is used only as reinforcement behind it, as What Are the Acrylic Shell and Stainless Steel Frame on a Walk-In Tub? explains.

How a Fiberglass Tub Is Made

The first video on this page is a walk-in tub installer comparing the two common constructions, acrylic and fiberglass. The installer describes fiberglass as a multi-layer system. It starts with a gel coat, which becomes the finished surface, and the tub is then built up behind that gel coat with fiberglass and resin. The result is a tub where the color and gloss sit in a thin top layer, and the strength comes from the layers behind it.

That order matters. In a fiberglass tub the surface is a coating over the structure. In a sheet acrylic tub the surface is a solid sheet of material that is heated and formed into the shape of the tub, and the fiberglass is added afterward to support it. Both tubs contain fiberglass. What differs is which material you sit on, clean and look at every day.

What Decides How Long a Fiberglass Tub Lasts

Ella's published material does not give a lifespan in years for a fiberglass tub, so this page does not quote one. What the sources do describe is where a fiberglass tub wears first, and that is the finish.

  • The gel coat is brittle. The installer in the video says the finish on a fiberglass tub is very brittle, and that fiberglass chips and fiberglass cracks.
  • The tub moves with temperature. The same video points out that these tubs expand and contract as hot and cold water moves inside them, which works against a brittle surface layer.
  • Repairs are involved. The installer describes going out to earlier fiberglass installations many times with a full fiberglass repair, then refinishing, buffing and polishing the surface.
  • The color sits on top. Ella's construction article notes that when the white runs through an acrylic sheet rather than sitting on top, it resists fading far better than a sprayed gel coat finish.

So the honest answer to how long a fiberglass tub lasts is that it depends on how well that thin surface layer holds up to daily use, temperature changes and cleaning. The structure behind it can outlast the finish, and when the finish fails it is the finish that has to be repaired.

Where Fiberglass Sits in an Ella Walk-In Tub

Ella does use fiberglass, but never as the bathing surface. Each shell starts as a solid acrylic and ABS sheet that is heated and vacuum-formed over a mold into one seamless surface. The team describes that acrylic as roughly 1/8 to 3/16 inch thick. Gel-coated fiberglass is then applied to the back for strength, the shell is set on a rust-proof stainless steel frame, and further fiberglass layers bond the shell and frame into a single structure.

No fiberglass is used on the bather side of the tub, so the surface you sit on and touch is acrylic throughout. What Are the Shell, Frame, Door and Towel Bar of an Ella Walk-In Tub Made Of? lists the materials of each part, and it also records the team's statement that a correctly installed tub does not off-gas volatile organic compounds.

The second video on this page looks under the tub. It shows the stainless steel frame and leveling legs on an Ella tub next to other walk-in tubs, including a fiberglass tub from a hardware store with a square tube steel frame and brackets molded straight into the fiberglass. It is a useful look at what sits behind the surface, which is the part of any tub you never see again once it is installed.

Fiberglass, Gel Coat, Sheet Acrylic and AcrylX Side by Side

Ella's showers add one more term. AcrylX is an acrylic finish applied over a fiberglass reinforced shell, and it replaced the gel coat finish used on older Ella shower units. What is AcrylX, and how does it compare to regular acrylic? covers that finish in full. The table puts the constructions next to each other using only what the sources state.

ConstructionSurface you touchWhat is behind itWhat the sources say about wear
Fiberglass tubGel coatFiberglass and resin built up in layersFinish described as very brittle, it chips and cracks, and repair means fiberglass repair, refinishing and polishing
Ella walk-in tubSolid acrylic and ABS sheet, roughly 1/8 to 3/16 inch thickGel-coated fiberglass reinforcement bonded to a stainless steel frameWhite runs through the sheet, the surface is non-porous, and dull spots or light scratches polish out
Ella AcrylX showerApplied acrylic finishFiberglass reinforced shellHigh gloss, truer white, resists scratching, cracking and chipping, less porous
Older Ella gel coat shower unitsGel coat finishnot listednot listed

What the differences mean for you: fiberglass is in every row, so the word alone does not tell you much about a tub or shower. The question to ask is what the surface is. A gel coat surface is a thin coating that carries all of the color and gloss. A sheet acrylic surface is solid material with the color running through it, which is why it can be polished back rather than refinished. Fiberglass behind the surface is a strength, and on Ella's shower stalls the side walls even have wood built into the fiberglass so a door frame can be screwed straight in, as Does the Ella Shower Stall Come With a Door, and What Size Door Fits the Opening? describes.

What a Mark in the Finish Means on an Ella Tub

Because the fiberglass reinforcement carries the structure and holds the water, a hairline crack that stays in the surface layer of an Ella tub is almost always cosmetic and is not a path for a leak. The same is true of a small indentation in the base. The support team can confirm this from a few clear photos, and a small mark can be blended with a brush-on appliance epoxy touch-up in a matching white. Hairline Crack or Small Dent in the Tub Finish: Why It Is Usually Cosmetic and How to Touch It Up gives the press test and the touch-up steps.

Day to day, the acrylic surface asks for very little. Use approved non-abrasive cleaners, avoid bleach and bath bombs, and never use abrasives. Dull spots and light scratches come back with a fine-grade automotive polishing compound. On the coverage side, Ella's Lifetime Limited Warranty lists the bathtub shell, frame and finish among the covered items, for parts only. If you have a question about a mark on your own tub, send photos through ellasbubbles.com/support or call (800) 480-6850 before you plan any repair.

Watch: Walk-In Tub With Rustproof Frame for Extended Lifespan, Voted Best/Safest 2020 | Ella’s Bubbles with chapters and a full transcript.

Common Questions

Is an Ella walk-in tub a fiberglass tub?
No. The bathing surface of an Ella walk-in tub is a solid acrylic and ABS sheet that is vacuum-formed into shape. Fiberglass is applied only to the underside as reinforcement, and no fiberglass is used on the bather side of the tub.
How many years does a fiberglass tub usually last?
Ella's published material does not state a number of years for a fiberglass tub. What it does describe is that the gel coat finish is the part that wears first, because it is brittle and can chip and crack. The life of a fiberglass tub therefore follows the condition of its surface layer.
Why does the finish on a fiberglass tub crack?
The installer in the video explains that a fiberglass tub is a multi-layer system that starts with a gel coat, and that this finish is very brittle. The tub also expands and contracts as hot and cold water moves inside it. That movement works against a brittle surface layer.
Does a hairline crack mean my Ella tub will leak?
Almost always it does not. The finish sits on top of fiberglass reinforcement that carries the structure and holds the water, so a crack that stays in the surface layer is cosmetic. Send photos through ellasbubbles.com/support or call (800) 480-6850 so the team can confirm it.
Is AcrylX on Ella showers the same as fiberglass?
No. AcrylX is an acrylic finish that is applied over a fiberglass reinforced shell. The shell gives the shower its shape and strength, and the AcrylX layer is the surface you see, touch and clean.
Can a dull spot on an acrylic tub be restored?
Yes. Dull spots and light scratches on the acrylic surface can be brought back with a fine-grade automotive polishing compound. Never use abrasives, and keep to approved non-abrasive cleaners for regular care.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket