The air jets on the seat and the lower air jets in the footwell floor are all fed by the same air pump, so if the seat jets blow, the pump is working. When a whole group of air jets stays quiet, the usual cause is an air line under the tub that slipped off, kinked or was routed to the wrong place, and the jets themselves are rarely the problem. How the system is laid out is covered in What Are Air Massage Jets on a Walk-In Tub?.
One Blower Feeds Every Air Jet
Pressing the Air button sends a puff of air to the control box, which starts the blower. The blower pushes air through lines under the tub and out through three groups of jets: upper jets in the seat and backrest, bidet jets at the base of the seat, and lower jets in the footwell floor. There is one blower for all three groups.
That layout tells you a lot when only part of the system bubbles. Seat jets that blow normally mean the button, the control box and the blower are all doing their job. What is left is the path the air takes from the blower to the footwell group, which is the set of air lines under the tub. The air jets are small brass jets built to be sat and stood on, so a whole row going quiet at once rarely points to the jets.
Check the Water Level Before Anything Else
Air massage needs a full-tub fill. Every air jet must be under water before you start the blower, including the ones up on the seat, because the air jets sit low by the feet and up on the seat. Fill the tub so that all of them are covered, and never fill above the center of the drain handle, which is the overflow line. The levels for each therapy are shown in What Is the Water Line Before Running the Jets on a Walk-In Tub?.
Then test from a known starting point:
- With the tub filled and the system off, press the Air button once. The first press is always high speed.
- Look at the seat and backrest jets, the bidet jets at the base of the seat, and the lower jets in the footwell floor, and note which groups bubble.
- Press again for medium, a third time for low, and a fourth time to turn the system off. Note whether the footwell group behaves the same way at every speed.
If the footwell air jets stay quiet with the tub properly filled and the blower on high, the fill level is not the cause and it is time to look under the tub.
Make Sure You Are Looking at Air Jets and Not Foot Hydro Jets
The footwell holds two different kinds of jets, and they belong to two different systems. As What Is the Footwell on a Walk-In Tub? describes, the foot hydro jets sit on a beveled edge angled at the heel and the ball of the foot, the calf jets sit a little higher, and on tubs with an air package the lower air jets are in the footwell floor.
The larger foot and calf hydro jets are a separate system from the air jets, so a working air massage tells you nothing about the foot pump. A few points keep the two apart:
- The Air button runs only the small air jets. Hydro jets have their own button and intensity dial.
- On tubs with Independent Foot Massage, the foot and calf jets have their own pump and their own button. The Ultimate operation video shows this on the deck: the three-speed air massage button, the hydro massage button for the back and hips, and a separate independent foot massage button with its own intensity dial.
- Without that option, the upper hydro jets share a pump with the foot jets, and the tub must be filled past the highest jets before any hydro button is pressed. How Do I Use Only the Foot Massage Without Filling the Whole Tub? explains how to tell which you have.
- The Standard, Standard60, Zen, Zen60 and Flow are hydro-only platforms and do not carry air jets, so any jets in the footwell of those tubs are hydro jets.
If the quiet jets turn out to be the foot and calf hydro jets, the cause is on the hydro side and the air line checks below do not apply.
When the Footwell Air Jets Are Truly Quiet: The Air Line
When a whole group or row of air jets stays dead while another group works, the usual cause is an air line under the tub that has slipped off, kinked or been routed to the wrong place. This is a check for a local contractor, who can open the access panel and look at the air lines with guidance from Ella technical support. Ella does not send technicians. Parts ship under the warranty, and a local licensed plumber or electrician does the labor.
If a jet cover or jet face is visibly damaged, that is a separate and smaller matter, because those parts can be replaced. Jets on the underside of the shell can break off if the tub is set down on them, which is why the tub is always lifted by the frame.
What to Send to Support
Send your serial number and photos so support can tell which line or part to look at. The serial number is on the label behind the magnetic access panel next to the door. For a ticket at ellasbubbles.com/support, or a call to (800) 480-6850, have these ready:
- Your model and serial number.
- Your therapy package.
- How the Air button responds to each press, and which jet groups bubble at each speed.
- Whether the Auto Purge fires after a bath. It starts on its own about 20 minutes after the air pump is turned off and runs for 120 seconds.
- How full the tub was when you tested.
- Photos of the footwell jets, and of the air lines behind the access panel if your contractor has it open.

Watch: Ultimate Walk-In Tub Guide: Ella's Bubbles Explained with chapters and a full transcript.
Related Guides
- Why Does the Air Massage Blow Cold Air? There Is No Heating Element
- Why Do My Air Jets Not Work Even Though the Auto Purge Still Runs?
- Air Jet Covers, Jet Faces, Tubing and Connectors: What Can Be Replaced and What Cannot Be Added Later
Related Videos
