Before an Ella walk-in tub goes in, your plumber has three things to plan: a path from the tub's 2 inch drain fitting to the house waste line, hot and cold supply lines brought to the faucet, and a floor the tub can be set level on so every leg carries equal weight. The best head start is to rough in the drain before the tub arrives, which is described in Choosing the Drain Side for an Alcove or Slab Installation and Prebuilding the Drain Line. A walk-in tub can also go in a spot that never had a tub, as long as a drain, a water supply and the right electrical line can be brought to that space.
The Three Plumbing Jobs in Plain Terms
An Ella walk-in tub arrives as a finished unit. Every tub is assembled and tested to order, with the pumps, motors and drain assembly fitted at the factory, so there is nothing for your plumber to mount in the field. What is left is ordinary bathtub plumbing, and it comes down to three tasks.
- The drain. The tub ships with its dual drain installed and four open ports, ready to be connected. Your plumber ties the 2 inch drain into the house drain line. Ella tubs drain by gravity alone, with no drain pump anywhere in the tub, so the route from the tub to the house drain deserves real attention. There is only about half an inch of clearance under the tub for the drain line to fall toward the house drain, and on a concrete slab a shallow trough in the concrete is worth considering.
- The water supply. The faucet is assembled on the deck at the factory, but it is not hooked up to the supply lines. Your plumber runs hot and cold to the faucet and makes those connections on site. The hand shower will not run until that is done.
- Setting the tub level. The tub stands on its own rustproof stainless steel frame. It has to be set level so every leg carries equal weight before the final connections are made.
Removing the old tub or shower, and any framing or floor work the opening needs, sits with your contractor as part of the same project.
Choose the Door Side First, Because It Decides the Drain Side
The most useful decision you can make before any pipe is moved is the door side. On an Ella walk-in tub the door and the drains are on opposite sides. A right-side door tub has its drains on the left, and a left-side door tub has its drains on the right, with sides described as you face the tub. That is why it helps to know which side of the room your plumbing wall is on before you order, since door side is one of the choices that appears on your order confirmation.
Existing rough-in plumbing does not have to dictate the choice. Installers often move the supply and drain lines to the side that gives the best access and the right door swing for the room. In a three-wall alcove the side walls are closed off once the tub is in, so the only way to reach the drain connections afterward is through the front of the tub. Plan the layout so the drain ports can be reached from the front, underneath the pumps, and the final connections can be made and checked without moving the tub. When your order is written up, read the item description carefully, because it states the hand of the tub.
What Your Plumber Can Do Before the Tub Arrives
We recommend having the drain roughed in before the tub arrives. The two drains sit on either side of the tub's center line, and their exact positions are dimensioned on the spec sheet for your model, so your plumber can locate the house drain connection ahead of delivery. A simple order of work looks like this:
- Settle the door side, which fixes the drain side on the opposite end.
- Ask the team at (800) 480-6850 for the spec sheet and the approximate drain distances for your model, and hand them to your plumber.
- Have the drain roughed in to suit those positions, and bring the hot and cold supply to the faucet end of the tub.
- When the tub is delivered, set it level, then make the final drain and supply connections on site.
If you found your installer through Ella's referral network, the installer receives the tub specifications and electrical diagrams for your model ahead of time, then visits your home to measure the space. Getting Installer Referrals and Leads for Your Walk-In Tub explains how that works. If you already have a plumber you trust, that works beautifully too. A licensed plumber who installs ordinary bathtubs can do this job, as covered in Can My Regular Plumber Install an Ella Walk-In Tub Without Special Training?
Putting a Tub Where There Has Never Been a Tub
A walk-in tub can go in a spot that never had a tub. The condition is that a drain, a water supply and the right electrical line can be brought to that space. A licensed local plumber runs the drain and supply lines to suit the new location, and a licensed electrician handles the power. When the tub goes in a different spot, the plumbing has to be redone to fit the new layout, so that part of the job is larger than a like-for-like replacement.
The simpler case is replacing an existing tub. Most Ella walk-in tubs fit the same three-wall alcove your current tub occupies, so the room layout and plumbing locations can stay where they are. When the tub is shorter than the alcove, an extension panel fills the gap, and a knee wall can hide the plumbing or carry fixtures. The end panel video on this page shows how this is finished: every Ella walk-in tub comes with one reversible end panel that covers the plumbing and the frame on the open end, and any tub less than 60 inches long comes with an extension panel so it fits a standard 60 inch tub alcove.
Access, Electrical and the Test Before the Walls Close
One rule shapes the whole layout: the tub must be installed with access left to both the plumbing and the electrical connections. The tub helps here. As the video shows, the front apron is removable and typically has two easily removable panels for service access to the plumbing and other components. Those panels also come off before the tub is carried into the house.
The electrical side is a separate task for a licensed electrician, on a dedicated GFCI circuit with the tub frame properly grounded. The plumbing and the electrical can be scheduled as separate jobs, but the tub's pumps need their circuits before the leak test that happens before the tub is closed in. Can I Install the Tub Before My Electrical Upgrade and Wire Jets Later? covers that order of work.
Testing happens twice. The installer fills the tub with water to check for leaks before it goes into the room, ideally while your existing bathing area is still usable, and then fills and runs it again after the connections are made and before the walls are closed. What happens during walk-in tub installation, and how long is the bathroom unusable? follows the full day step by step. Ella manufactures and supports the tub and does not install it, so a licensed local plumber and electrician do this work, and Ella's technical support is happy to help them at (800) 480-6850.

Watch: Ella's Bubbles: End Panels And Extension Panels with chapters and a full transcript.
Related Guides
- What Size Water Heater Do I Need for My Walk-in Tub?
- Electrical requirements by model: dedicated GFCI circuits for your walk-in tub
- How fast does a walk-in tub drain after a bath?
Related Videos

