Support Center / Replacement Parts / What Size Are the Union Nuts on the Walk-In Tub In-Line Heater?
Back to Replacement Parts

What Size Are the Union Nuts on the Walk-In Tub In-Line Heater?

The unions at the hydro pump and the in-line heater on an Ella walk-in tub are nominal 2 inch PVC. We do not publish a replacement union nut part number, so the team confirms the right part from your model, your serial number and a photo of the union. If a drip is the reason you are asking, the nut is rarely the problem: How Do I Fix a Leaking Union Gasket at the Pump or Heater? gives the re-seat routine that solves most union leaks without any new part.

The Size, and Why the Part Is Confirmed by Photo

The in-line heater is part of the hydro massage system. It is plumbed in line with the hydro pump, and unions join it to the pipework so the joints can be undone and remade. Those unions are nominal 2 inch PVC, the same as the unions at the hydro pump.

A replacement part number for the union nut is not listed here, and that is deliberate. The serial number tells the team when the tub was made and which replacement parts are compatible with it, so the right part is matched to your tub instead of guessed from a general list. To have the part confirmed, open a ticket at ellasbubbles.com/support or call (800) 480-6850 with:

  • Your model.
  • Your serial number. The serial label is behind the magnetic access panel next to the door.
  • A clear photo of the union, showing the nut and the fitting on each side of it.

The serial number video on this page shows where that label sits, on the inside of one of the removable panels, and explains that it lets the team see when the tub was made and which replacement parts are compatible. The in-line heater video shows what the heater does: when you engage the hydro massage, the heater works with the water pump to maintain a consistent warm temperature.

The Joints Under the Tub, Side by Side

Several threaded connections sit close together under a walk-in tub, and people use the words union and nut for more than one of them. This table sorts them by size and by what actually seals each one, using only the figures in Ella's guides.

JointSizeWhat seals itWhat it means for a repair
Union at the in-line heaterNominal 2 inch PVCO-ringTake apart, re-seat the O-ring, reassemble snug by hand; check that the heater threads match the pipe threads
Union at the hydro pumpNominal 2 inch PVCO-ringTake apart, re-seat the O-ring, reassemble snug by hand
Drain union nut, PVC elbow to brass drain2 inch drain; standard 2 inch PVC fittings work under an Ella tubRubber gasket with two faces, only one sealsFlip the gasket so the sealing face sits against the brass, then hand tighten only
Plug on the hydro return elbownot listed100 percent siliconeThe one spot under the tub where silicone belongs

What the differences mean for you: the heater and pump unions share the same nominal size and the same sealing method, so the same repair applies to both. The drain union looks similar but seals on a two-faced rubber gasket, not an O-ring, and Where Do the Extra Rubber Gaskets in My Tub Parts Box Go? shows where those gaskets belong. None of these joints seal on their threads, which is why Should I use thread tape or sealant on walk-in tub drain and union fittings? explains that Ella's repair guides do not call for tape or pipe sealant at the unions.

If a Drip Is Why You Are Asking

Most people who look up a union nut size have a union that weeps. A union at the pump or heater that keeps dripping after it has been tightened almost always has an over-tightened or displaced O-ring. No amount of extra force will make a displaced O-ring seal, and the water finds the gap beside it every time the pump runs. A new nut does not change that, and in most cases nothing has to be replaced.

The published fix is short:

  1. Switch the pumps off and dry the union.
  2. Take the union apart.
  3. Re-seat the O-ring squarely in its groove.
  4. Reassemble the union snugly by hand instead of continuing to turn the nut.
  5. Run the hydro pump and watch the joint with a flashlight.

At the heater, also check that the heater threads match the pipe threads before you reassemble. Over-tightening is what pushes the O-ring out of place, so snug by hand is the goal. Never start a pump until the tub is filled.

Confirm the Heater Union Really Is the Source

Water that collects under the tub can come from several connections, so isolate the source before you open anything. Open the access panel, dry the whole cavity, and lay dry paper towels under the pump, the heater, the drain fittings and the faucet connections. Fill the tub with the pumps off and wait. If a towel gets wet now, the water is not coming from a union. Then run the hydro pump alone for several minutes and look at the unions at the pump and at the heater with a flashlight. Water that shows only while the jets run usually comes from a union at the pump or heater, not the drain.

The unions are also the joints most likely to shift in transit, because shipping vibration can loosen unions and air lines. That is why every Ella tub gets a fill test before the walls close, and why Ella's pre-installation guidance calls a union drip found during that test a normal install-stage adjustment, not a defect. The warranty activation form's pump check runs the hydro system for at least 20 minutes while every connection is confirmed watertight, as Does the In-Line Water Heater Need Checking for the Warranty Activation Checklist? describes.

If a Part Does Turn Out to Be Faulty

If the nut, the union or the heater fitting is cracked or damaged, stop tightening and photograph it. Send the photo with your model and serial number through ellasbubbles.com/support or call (800) 480-6850. Once the team has verified the problem, the part ships under the parts warranty, and your local licensed plumber does the labor. Ella's Bubbles does not send technicians, so it helps to have your plumber's visit planned around the part's arrival.

Video

Watch: Ella's Bubbles: In-line Water Heater Maintains Comfortable Water Temperature with chapters and a full transcript.

Common Questions

What size are the unions on the in-line heater?
The unions at the hydro pump and the in-line heater are nominal 2 inch PVC. Send a photo of the union with your model and serial number so the team can confirm the exact part for your tub.
Is there a part number for the heater union nut?
We do not list a replacement union nut part number. Open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your model, serial number and a photo of the union, and the team will confirm the right part to send.
Why does my heater union still drip after tightening?
A union that leaks after tightening usually has an O-ring that has been over-tightened or pushed out of its seat. Take the union apart, re-seat the O-ring squarely and reassemble it snug by hand. At the heater, also check that the heater threads match the pipe threads.
Should I put thread tape on the heater union?
No. Ella's published repair guides do not call for thread tape or pipe sealant at the unions. The joint seals on an O-ring, so the water is getting past the O-ring, not through the threads.
Where is the serial number the team asks for?
The serial label is behind the magnetic access panel next to the door. It lets the team see when the tub was made and which replacement parts are compatible.
Is a faulty union part covered under the warranty?
If a part does turn out to be faulty, it ships under the parts warranty once the team has verified the problem. The warranty covers parts only, so a local licensed plumber does the labor.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket