Support Center / Sizes, Fit & Measuring / What Fills the Gap Beside My Tub If No Extension Panel Is Made?
Back to Sizes, Fit & Measuring

What Fills the Gap Beside My Tub If No Extension Panel Is Made?

If no extension panel is made for your tub, the gap between the tub and the wall is closed with site built framing by your installer, a short framed and finished section rather than a factory filler. The reversible end panel that ships with the tub covers an exposed end, but it adds no length, so it cannot close a gap to a wall. What Happens to the Leftover Space If My New Walk-In Tub Is Smaller? looks at leftover space in general, and this page stays with the tubs that have no extension panel of their own.

Two Panels That Are Easy to Confuse

Most questions about a side gap come from mixing up two different parts, so it helps to separate them first.

  • The end panel covers an exposed short end of the tub, hiding the plumbing and the frame. Every Ella walk-in tub ships with one reversible end panel that can go on the left or the right, and a second end panel can be purchased when both ends are open. It finishes an end you can see. It does not reach across to a wall.
  • The extension panel, also called a filler kit, is the part that closes a gap along the length of the alcove. It rests on adjustable stainless steel shelf brackets that are part of the tub frame, it is trimmed on site, and it doubles as a handy shelf. What Is an Extension Panel (Filler Kit) on a Walk-In Tub? explains the part in full.

Two models handle the end panel a little differently. The Front Entry comes with two side panels instead of the single reversible end panel, and the Standard has a non-reversible end panel on the faucet side. The video on this page shows both panel types on a tub: the reversible end panel placed on the open side when the tub sits in a corner, and the extension panel used so that a tub under 60 inches fits a standard 60 inch alcove.

Which Tubs Have an Extension Panel and Which Do Not

OptionWidth or size listedModelsWhat it means for the gap
Extension panel7 inch panelStandard, Ultra, Elite, Petite, RoyalTakes the tub to a standard 60 inch alcove
Extension panel4 inch panelDeluxe, at 55 inches longTakes the tub to a standard 60 inch alcove
Extension panel8 inch panelCapri, Transfer26, Transfer30, Transfer32Takes the tub to a standard 60 inch alcove
Extension panel5 inch panelTransferXXLTakes the tub to a standard 60 inch alcove
Extension panelnot listedZen and Flow (included), Monaco and Lounger (available)Panel for 60 inch alcoves
No extension panelnot listedMobile, Front Entry, Big4One, Shak, Ultimate, Standard60, Zen60, Transfer60, two-seat modelsAny gap at the wall is framed and finished by the installer
Reversible end panelAdds no lengthEvery Ella walk-in tub, one includedCovers an exposed end only, never a gap to a wall

What the table means in practice: if your tub is on one of the first five rows, a matching factory panel is the normal answer and your installer trims it to the wall. If your tub is on the sixth row, there is no factory filler to wait for. Several of those tubs are full-length models that fill a standard alcove on their own, so the question only comes up when the opening is longer than the tub. The 45 inch Mobile is the one most likely to leave a real stretch of open space, since it is the shortest standard size, and the Big4One is another model where a gap at the wall is closed by framing.

How Your Installer Closes the Gap When There Is No Panel

On a model where no extension panel is offered, the gap at the wall is closed with site built framing: a short framed and finished section built by your installer as part of the bathroom work. It is ordinary carpentry and finishing, planned around the tub, and it is how the room ends up looking built in when no factory part exists for that model.

Good measurements make the difference, and they need to happen before anyone frames:

  1. Measure the opening wall to wall at the back and at the front. Alcoves are rarely square, so the two figures often differ.
  2. Allow for the finished walls. Tile and drywall have thickness, and the gap you frame is the gap left after the walls are finished, not the gap between bare studs.
  3. Measure from the finished walls and the floor, never from the rim of the old tub. The tub you are removing may itself be smaller than the opening it sits in.
  4. Decide where the gap goes. If the space is split so there is a gap on each side, each one is framed and finished the same way.

The same approach applies on a tub that does have an extension panel when the opening is longer than the panel can cover. The panel closes what it was made for, and your installer frames and finishes the remaining space.

When the Space Is Front to Back, or the End Is Open

Not every gap runs along the length of the tub. If the tub is narrower from the back wall to the front edge of the alcove, there is no factory filler for that direction on any model. The extension panel works along the length only, so that figure is measured separately and your licensed installer finishes any remaining space. How is the gap filled if the tub is narrower than my alcove? sorts out the two directions.

If the space beside the tub is not a gap to a wall at all, but an open, freestanding end, that is the job of the reversible end panel. One is included, and a second can be purchased through where you purchased the tub when the tub sits against the back wall with both ends open.

On tubs that do take an extension panel, the panel is built for one end. The panel side is chosen when the tub is configured, and on a Capri or Elite the shelf brackets can be fitted to both ends only when that is requested before the tub is built. Why Doesn't the Extension Panel Attach on the Faucet Side? covers that situation.

What to Confirm Before Installation Day

  • Which panels came with your tub. Our team can confirm exactly which panels were supplied if you have the model and serial number ready. The serial number is on the label behind the magnetic access panel next to the door.
  • Whether a panel exists for your model. Check the table above, then confirm with your Ella dealer or the team at (800) 480-6850 so your installer plans for framing or for a panel, not both.
  • Whether you need every panel. If your installation will not use the end panel or the extension panel, you can opt out of receiving it to reduce plastic waste.
  • How the tub will be carried in. All removable panels, including the front apron, the end panel and any extension panel, must be removed before the tub is moved into the house and into the bathroom.

One more point for mixed bathrooms: an Ella extension panel depends on the Ella frame, so it is not a universal filler beside another maker's tub. Can I Use an Ella Extension Panel Next to a Non-Ella Tub? explains why.

Video

Watch: Ella's Bubbles: End Panels And Extension Panels with chapters and a full transcript.

Common Questions

Can the reversible end panel close a gap to the wall?
No. The end panel covers an exposed short end of the tub, hiding the plumbing and the frame, but it adds no length. A gap to a wall needs an extension panel where one is offered, or site built framing where one is not.
Which Ella tubs do not have an extension panel?
The Front Entry and the Mobile do not use one, and neither do full-length tubs such as the Ultimate, Standard60, Zen60, Transfer60, Big4One, Shak and the two-seat models. On those tubs any gap at the wall is framed and finished by the installer.
Who builds the framed section beside the tub?
Your installer builds it as part of the bathroom work. It is a short framed and finished section made on site rather than a factory filler, so it is planned and measured for your specific opening.
How should the gap be measured before it is framed?
Measure the opening wall to wall at both the back and the front, because alcoves are rarely square. Allow for the thickness of tile and drywall on the finished walls, and measure from the finished walls rather than from the rim of the old tub.
What if there is open space at both ends of the tub?
If both ends are open and visible, the included reversible end panel covers one end and a second end panel can be purchased for the other. If the space at each end runs to a wall and no extension panel is made for your model, your installer frames and finishes each side.
How do I find out which panels came with my tub?
Have your model and serial number ready and contact your Ella dealer or the team at (800) 480-6850, or open a ticket at ellasbubbles.com/support. The serial number is on the label behind the magnetic access panel next to the door.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket