Support Center / Showers, Panels & Accessories / Who offers custom walk-in shower remodeling with a low-threshold entry?
Back to Showers, Panels & Accessories

Who offers custom walk-in shower remodeling with a low-threshold entry?

A local licensed remodeling contractor carries out a custom walk-in shower remodel with a low-threshold entry, and Ella's Bubbles builds the low-threshold shower base, the stall and the wall panels that the contractor installs. Ella does not send technicians or perform installations, as Who can install a walk-in tub, shower pan or walk-in shower? explains. This page shows how the two halves of the project fit together: what Ella makes, what your contractor does, how low the entry can be, and the order that takes a custom shower from an idea to a finished bathroom.

Who Does Which Part of the Remodel

A low-threshold shower remodel has two parties, and it helps to know from the start which one you are talking to about what.

  • Ella's Bubbles makes the shower. Ella builds the pieces to your dimensions, ships them as finished pieces, and answers your contractor's questions during the work with manuals and live video help, as well as by phone and email.
  • Your contractor does the remodel. The drain connection is plumbing work and the wall panels bond to the existing wall surface, so a licensed plumber or a remodeling contractor who does bathrooms can carry the whole job. The base and the walls are installed in sequence by the same person, not as two separate trades.

Any licensed installer is fine, and certification by Ella is not required. If you do not have a contractor, the team can refer installers from its nationwide network. Labor is arranged and paid for between you and the contractor, and Ella does not estimate it.

The contractor you choose matters for your coverage too. Improper or negligent installation and modifications by anyone other than Ella's Bubbles are excluded from coverage, and labor is warranted by the independent contractor who did the work. A licensed installer who follows the manual protects the warranty as well as the bathroom. Questions that come up on site go to your Ella dealer or the team at (800) 480-6850.

How Low the Entry Can Be

Low threshold covers two different entries. One has a low raised edge that you step over. The other has no curb at all, so a wheelchair or shower chair rolls straight in. What is the difference between a roll-in and a walk-in shower? covers the naming, and the table below sets out the Ella options with the figures printed in the published shower pages. Where a figure is not printed, the cell says so.

OptionEntry or thresholdSizes printed in the sourcesBest for
Step-in threshold base3 inch step-in thresholdnot listedA bather who can lift a foot over a low edge and would rather not rely on a dam
One-piece or three-piece shower stall4 inch thresholdnot listedA complete stall that ships with the grab bar set listed for that kit and the drain in the carton
AcrylX barrier-free roll-in baseBeveled roll-in entry of 3/4 inch to 1 1/8 inch depending on size30 x 60, 32 x 60 and 36 x 60 inches, with other sizes made to orderA bather who stays in a wheelchair or shower chair and rolls straight in
SMC barrier-free roll-in base1 inch or 1 1/8 inchnot listedThe lowest entry of any Ella product

What the differences mean for you is simple. The step-in base has a raised edge molded into it, and that edge holds the water inside the shower without a dam. The step over it is far lower than the side of a conventional tub. A roll-in base removes the edge entirely, so there is nothing molded into the base to hold the water back. Ella pairs the roll-in base with a collapsible rubber shower dam. The wheels of a chair compress it on the way in and out, and it returns to its original shape to keep the water in the shower. If a wheelchair user will bathe in the shower, the roll-in base is the better fit, because nothing has to be crossed at the entry. If the bather can step, the 3 inch step-in base is the answer.

What Makes the Shower Custom

The custom part of the project lives in three places: the base, the drain and the walls.

  • The base. Custom shower bases can be ordered to specific dimensions, such as a 36 by 36 inch corner base. Barrier-free roll-in bases with a low threshold are available in a 32 by 60 inch size, and the AcrylX barrier-free line is made to order in other sizes beyond the ones printed. Walk-In Tub and Shower Base Sizes and How to Measure for Fit lists the sizes and how to measure.
  • The drain. The drain can be placed to your exact measurements, for example 9 and 5/8 inches from each of two adjacent walls. That lets the new base meet the drain line your bathroom already has. The online drain-placement tool can round measurements up to the nearest inch, so it is a good idea to confirm your exact drain location with the team at (800) 480-6850 before your base is built.
  • The walls. The wall surround is the component that is cut on site, and the base never is. Ella's cultured marble panels come as eight, six or four panel surrounds, and their factory finished edges can be trimmed and cut on site for a custom fit to the width and height of your alcove. They glue over drywall, plaster, painted walls, cement board or even existing tile, so the contractor does not need to strip the room to the studs. Ella also makes shower wall panels at 98 inches high in a plain white finish.

Because the base is molded to size and never trimmed, the measurements you give at the start decide how well everything fits. The walls give your contractor room to adjust, and the base does not.

The Order a Custom Low-Threshold Remodel Follows

  1. Decide how the bather will enter. Choose between stepping over a low edge and rolling in with no curb, using the table above.
  2. Build a design. The Shower Builder Tool lets you scroll through the available options online and put together a custom shower design. It gives you a starting point for discussing the project with your Ella dealer or the team at (800) 480-6850.
  3. Have a contractor measure. After you build your design, a contractor visits in person to measure your space and finalize the installation details for your new shower.
  4. Confirm the base and the drain. Settle the base dimensions and the exact drain location before the base is built.
  5. Set the base. The base goes in first, on a floor prepared so the drain line lands where the drain sits on the pan you ordered. The drain connection is plumbing work.
  6. Finish the walls. The walls are finished above the base with a wall system sized to that base. Your contractor checks the surface the panels will bond to, trims the panel edges to fit the alcove, glues the panels in place and joins the edges.
  7. Mount the grab bars. Grab bars are mounted as part of the wall work, as Who installs acrylic shower walls and shower pans in my bathroom? describes for the whole wall side of the job.

What to Have Ready Before You Call a Contractor

A contractor can give you a clearer answer when you arrive with the basics already gathered. Before the first conversation, have these ready:

  • The width, length and height of your existing tub or shower alcove.
  • Where the drain sits now, measured from the walls.
  • Whether the bather will step in or roll in, and whether a wheelchair or shower chair is part of the plan.
  • The design you built in the shower builder, so the contractor can see what you have in mind.
  • The wall surface the panels will bond to, whether drywall, plaster, paint, cement board or tile.

With those in hand, your contractor can confirm the fit on the measuring visit, and any product question that comes up goes to your Ella dealer or the team at (800) 480-6850. The support pages at ellasbubbles.com/support hold the guides your contractor may want to read before the work starts.

Common Questions

Does Ella's Bubbles install the low-threshold shower itself?
No. Ella's Bubbles builds the base, the stall and the wall panels and ships them as finished pieces, but it does not send technicians or perform installations. A local licensed plumber or remodeling contractor does the work, and Ella supports that contractor with manuals and live video help.
How low is the threshold on an Ella walk-in shower?
Ella's step-in base has a 3 inch threshold, and the one-piece and three-piece stalls have a 4 inch threshold. The barrier-free roll-in bases go lower. AcrylX bases have a beveled entry of 3/4 inch to 1 1/8 inch depending on size, and SMC bases are 1 inch or 1 1/8 inch.
Can the shower base be made to fit my existing drain?
Yes. Custom shower bases can be ordered to specific dimensions with the drain placed to your exact measurements, for example 9 and 5/8 inches from each of two adjacent walls. Confirm the exact drain location with the team at (800) 480-6850 before the base is built, because the online drain-placement tool can round measurements up to the nearest inch.
Do I need a contractor who is certified by Ella?
No. Any licensed installer is fine, and certification by Ella is not required. If you do not have a contractor, the team can refer installers from its nationwide network.
Does a roll-in shower with no curb keep the water in?
Yes, with the help of a dam. A roll-in base has nothing molded into it to hold the water back, so Ella pairs it with a collapsible rubber shower dam. The wheels of a chair compress the dam on the way in and out, and it returns to its original shape to keep the water in the shower.
Do the walls have to be stripped to the studs?
No. Ella's cultured marble wall panels glue over drywall, plaster, painted walls, cement board or even existing tile. Your contractor trims the factory finished edges on site to fit the width and height of your alcove.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket