Support Center / Plumbing & Electrical / Is the Ella 5-Piece Fast-Fill Faucet ASME and ANSI Tested and Approved?
Back to Plumbing & Electrical

Is the Ella 5-Piece Fast-Fill Faucet ASME and ANSI Tested and Approved?

The Ella spec sheet calls out one ASME standard for the faucet hardware: ASME A112.18.1, printed beside the picture of the handheld sprayer, and that standard applies to plumbing supply fittings. Ella's published guidance does not present the 5-piece Fast-Fill as the ASME-certified faucet option. When an inspector requires the faucet itself to be ASME certified, the Huntington Brass faucet is the one to specify, as My Inspector Wants ASME A112.19.15 Certification for the Tub or Faucet: What Ella Can and Cannot Provide explains.

What the Spec Sheet Actually Shows for the Faucet

The current spec sheet for each model is the document to look at first, because it is what Ella sends to inspectors and plan reviewers. On that sheet, the faucet-related standard is ASME A112.18.1, and it appears beside the picture of the handheld sprayer. A112.18.1 is the standard for plumbing supply fittings, which is the family a faucet and its hand shower belong to. It is a different document from the bathtub standards that inspectors sometimes quote for a tub with a door.

That placement matters. The callout sits with the handheld sprayer image, and the sources Ella publishes stop there. They do not state that the complete 5-piece Fast-Fill set carries an ASME certification, and this page does not claim one. If your inspector needs a yes or no on the faucet set as a whole, the dependable route is to put the faucet spec sheets in front of the inspector and let the documents speak.

Which Standard Applies to Which Part of the Tub

Much of the confusion comes from several standard numbers being quoted together, when some describe the faucet and others describe the tub or its electrical equipment. The table sorts them out.

StandardWhat it coversWhat it means for the faucet question
ASME A112.18.1Plumbing supply fittingsThe faucet-side standard. Called out on the spec sheet beside the handheld sprayer.
CSA B125.1Faucets, published by CSA GroupThe Canadian faucet standard an inspector in Canada may name.
ASME A112.19.15Bathtubs and whirlpool bathtubs with doors made watertight by a pressure sealA tub standard, not a faucet standard. It does not answer a faucet question.
UL 1795Hydromassage bathtubsThe standard the tub is built to conform to. Not a faucet listing.
CSA C22.2 No. 218.2The Canadian standard for the same tub equipmentApplies to the tub. Not a faucet listing.
ETLListing mark on pumps, in-line heaters and electrical componentsElectrical components only. The faucet is not an electrical component.

What this means for you: if an inspector asks whether the faucet is ASME or ANSI approved, the relevant number is the supply fittings standard, A112.18.1, and the relevant documents are the faucet spec sheets. The tub's UL, CSA and ETL information answers a different question, the safety of the hydromassage tub and its electrical equipment. That information lives on the tub's label, and What a UL, ETL or CSA Listing Covers and How to Read the Label on a Walk-In Tub shows how to read it.

The Two Factory Faucets and What an Inspector May Require

Ella installs one of two faucets at the factory: the Huntington Brass faucet or the Ella Fast-Fill faucet. The guidance for inspections is direct.

  • If the inspector requires the faucet itself to be ASME certified, choose the Huntington Brass option.
  • If the inspector simply wants to see what the faucet is built to, the team can send the spec sheets for both faucets so the inspector can compare them side by side.
  • If the review calls for thermostatic mixing at the fixture, that is a separate choice. Tubs equipped with an Ella thermostatic faucet package include a built-in Ella Thermostatic Control Valve that mixes hot and cold to a set temperature.

The 5-piece Fast-Fill is a popular set for good reason. The Ella Standard, for example, ships with the 5-piece Ella Fast-Fill faucet with a pull-out hand shower, and the shower column kit connects to the diverter on the two-piece or five-piece fast-fill faucet set. None of that changes with an inspection. The only question an inspector raises is which document supports the faucet, and that is settled on paper.

Settle It Before the Tub Ships

Timing is the practical point most owners miss. The faucet is fitted before the tub ships, so the best moment to resolve a certification requirement is when the order is placed with your Ella dealer or the team at (800) 480-6850.

  1. Ask your inspector or plan reviewer, in writing if you can, exactly which standard they want to see for the faucet and which for the tub.
  2. Request the spec sheets for both the Huntington Brass and the Ella Fast-Fill faucets, along with the current spec sheet for your model.
  3. Share them with the inspector before you confirm the faucet on your order.
  4. If the inspector requires an ASME-certified faucet, specify the Huntington Brass option on the order.

If your tub has already shipped with the Fast-Fill faucet and the inspector will not accept it, contact the team at ellasbubbles.com/support or (800) 480-6850 before the re-inspection so they can advise on your options. Raising it early avoids a second trip for everyone.

What Else Ella Can Send Your Inspector

A faucet question often arrives with a broader request for paperwork. Alongside the faucet spec sheets, Ella can provide the tub's electrical safety listing, shown as a UL, ETL or CSA mark on the tub's label, and the current spec sheet for your model. The marks, where the label sits and what they mean for a Canadian installation are covered in Safety Certifications on Ella Tubs and Faucets: UL, ETL, CSA and IAPMO Marks, Where the Label Is, and What They Mean for Canada.

For a facility project, where a plan reviewer may also ask about temperature control and compliance documents, Can Ella Walk-In Tubs Be Installed in Nursing Homes, Assisted Living and Long-Term Care Facilities? lists what reviewers usually request. Certification marks describe the equipment. They do not replace a licensed plumber or electrician, or your local code requirements.

Common Questions

Which ASME standard is printed on the Ella spec sheet for the faucet?
The spec sheet calls out ASME A112.18.1 beside the picture of the handheld sprayer. That standard applies to plumbing supply fittings, not to the tub shell.
Which Ella faucet should I choose if my inspector requires ASME certification?
Choose the Huntington Brass faucet option. Ella's guidance is that when an inspector requires the faucet itself to be ASME certified, the Huntington Brass is the one to specify.
Can Ella send the Fast-Fill faucet spec sheet to my inspector?
Yes. The team can send the spec sheets for both faucets Ella installs, the Huntington Brass and the Ella Fast-Fill, so the inspector can compare them. Request them through your Ella dealer, ellasbubbles.com/support or (800) 480-6850.
Does ASME A112.19.15 apply to the 5-piece Fast-Fill faucet?
No. ASME A112.19.15 covers bathtubs and whirlpool bathtubs with doors made watertight by a pressure seal. It is a tub standard, so it is not the number to look for on a faucet.
What if my tub already shipped with the Fast-Fill faucet?
If the inspector will not accept the Fast-Fill faucet, contact the team before the re-inspection so they can advise on your options. Because the faucet is fitted before the tub ships, it is always easiest to settle this when the order is placed.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket