Support Center / Showers, Panels & Accessories / Can I install an SMC shower niche into an existing tiled shower wall?
Back to Showers, Panels & Accessories

Can I install an SMC shower niche into an existing tiled shower wall?

Yes, in principle. The Ella SMC niche is designed for solid shower walls and stud walls, and its published steps begin with cutting a cavity into a wall, so a wall that is already tiled can take one. The published instructions do not give a separate retrofit procedure for a finished tile wall, though, and because the flange of the niche is fixed to the framing, waterproofed and then tiled over, the tile around the opening becomes part of the job. The full sequence is in Installing SMC Shower Niches and Soap Dishes, and this page explains what that sequence means when the wall is already finished.

What the Published Instructions Cover, and What They Leave Out

Every Ella SMC niche is molded with a 3/16 inch wall, a non-porous surface that resists mold and stains, and a flange around the opening. The body is 3 1/2 inches deep and the recessed installation depth is 4 inches. The niche is recessed between two studs, and the flange is what ties it into the wall.

The instructions are written around one requirement: the flanges must end up flush with the plasterboard surface before tiling. They do anticipate an existing wall, because one step tells the installer to notch the existing plaster or pack behind the flanges with wooden strips, which are not supplied, until the flanges sit flush. What they assume is that the wall finish goes on afterward. The waterproofing is applied over the flange, the tile is laid over the flange, and silicone finishes the joint.

In a wall that is already tiled, that order still applies. The flange belongs behind the tile layer, not on top of it. So the niche does not simply drop into a hole cut through finished tile. The tile around the opening is opened up, the niche is set and waterproofed, and the tile is then finished over the flange.

Three things are not published, and your contractor decides them on site:

  • A method written specifically for cutting through finished tile. The instructions say only that the opening is cut with a saw or an angle grinder.
  • How far back the existing tile has to be removed around the opening.
  • How the new waterproofing meets whatever waterproofing is already behind your tile.

The team at (800) 480-6850 can answer your installer's questions about the niche itself.

Which Niche, and How Much Wall Each One Opens

OptionPublished sizeHow it mountsWhat it means in a tiled wall
Single niche14 inches wide by 16 inches high by 3 1/2 inches deepRecessed between two studs, 4 inch installation depthThe smallest opening to cut and the least tile to refinish
Dual niche16 inches wide by 27 inches high by 3 1/2 inches deep, two compartmentsRecessed between two studs, 4 inch installation depthA taller opening, so more tile is disturbed
Triple niche16 inches wide by 39 inches high by 3 1/2 inches deep, three compartmentsRecessed between two studs, 4 inch installation depthThe tallest opening and the most storage
SMC soap dishSize not listedSurface-mounted through two 5/32 inch holesNo cavity at all, only two holes and sealing

The three niches are the same depth, so the wall has to offer the same 4 inches whichever one you choose. What changes is the height of the opening, from 16 inches to 39 inches, and with it the amount of finished tile that has to be opened and made good. If the goal is a place for soap and you would rather disturb as little tile as possible, the surface-mounted soap dish is the option that avoids a cavity entirely.

Four Checks Before Anyone Cuts the Tile

  1. The stud bay. The niche is centered between two studs. Horizontal noggins are added between the studs at the top and bottom so the framed opening matches the niche dimensions.
  2. The depth. Confirm the full 4 inch depth is available behind the wall surface. A wall that cannot give that depth cannot take a recessed niche.
  3. Hidden services. The instructions call for checking for hidden pipes, cables and screws twice, once before marking the wall and again before cutting. If anything runs through the bay you want, that is a question for a local licensed plumber or electrician before the cut is made.
  4. The finished wall thickness. Note how thick the finished wall is, because that decides how much notching or packing is needed for the flanges to sit flush before the tile goes back.

When the location is settled, mark the recessed body of the niche on the wall, not the flange outline. The cavity is cut for the body. The flange sits against the wall around it.

How the Published Steps Play Out in a Finished Shower

Before any cutting, protect the shower tray and cover the drain so debris cannot enter. Dry-fit the niche and mark every location first, and have a second person help mark and set it. Use a spirit level throughout.

  1. Cut the opening with a saw or angle grinder, then smooth the edges and clean up.
  2. Fit the noggins at the top and bottom, push the niche in gently and check the surface levels.
  3. Set the depth by notching or by packing behind the flanges with wooden strips until the flanges sit flush.
  4. Screw the niche to the framing without over-tightening.
  5. Waterproof with a self-adhesive membrane and sealing compound.
  6. Tile over the flanges.
  7. Finish with silicone at every stated joint and let it cure for 24 hours before the first shower.

Waterproofing goes on before the tile and silicone goes on after it. The published guidance names the type of product at each stage but not a brand, as Which Silicone or Adhesive Do Ella SMC and Acrylic Wall Kits Use? explains.

Because the tile is laid over the flange, it is worth confirming you have tile to finish around the opening before the wall is cut. Until installation day, open the packaging carefully and never cut into it with a blade. Store the niche flat, not leaning against a wall, and keep it out of wet or humid conditions.

If You Would Rather Not Open the Wall

A recessed niche is not the only way to add storage to a finished shower. Besides the surface-mounted SMC soap dish, Ella's add-on shelving includes a flush mount single shelf at 2 1/2 by 16 1/4 inches and corner caddies with one or two shelves. They are listed in What shelving does an Ella shower have, and how big are the shelves? If you are deciding how many shelves the bather actually needs, and at what height, How many corner shelves should a walk-in shower have? works through that by who reaches for the shelf.

If the old tile is the real problem, there is another route. Ella's cultured marble surrounds can be glued over existing tile, and acrylic wall panels are cut on site where they have to go around a niche, as described in What Are Acrylic Shower Walls and How Are They Cut to Fit? For help choosing between these, reach your Ella dealer or the team at (800) 480-6850, or open a request at ellasbubbles.com/support.

Common Questions

Do the instructions include a method for an existing tiled wall?
No. The published steps describe cutting a cavity, setting the flanges flush with the plasterboard, waterproofing and then tiling over the flanges. They do not give a separate procedure for cutting through finished tile, so your contractor decides how the tile around the opening is opened and refinished.
How deep does the wall need to be for an SMC niche?
The niche body is 3 1/2 inches deep and the recessed installation depth is 4 inches. The instructions tell the installer to confirm the full 4 inch depth after cutting the cavity. All three niche sizes need the same depth.
Can the niche flange sit on top of my tile?
The published instructions do not describe that. They call for the flanges to sit flush with the plasterboard surface before tiling, with waterproofing over the flange and tile laid over it. The flange is meant to end up behind the tile, not on its face.
How long before I can shower after the niche is installed?
The final silicone needs 24 hours to cure before the first shower. That silicone is the last step, applied after the waterproofing and the tile are finished.
Is there a storage option that needs no cavity in the wall?
Yes. The SMC soap dishes are surface-mounted through two 5/32 inch holes and sealed the same way as the niche. Ella also lists a flush mount single shelf at 2 1/2 by 16 1/4 inches and corner caddies with one or two shelves as add-ons.
What should be checked before cutting into the shower wall?
Check for hidden pipes, cables and screws before marking the wall and again before cutting. Center the niche between two studs, note the thickness of the finished wall, and mark the recessed body, not the flange outline. Protect the shower tray and cover the drain so debris stays out.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket