No, you do not need 3/4 inch house plumbing to use an Ella fast-fill faucet. Every Ella 2-piece and 5-piece fast-fill faucet set ships with two 3/4 inch by 5 foot braided stainless steel supply lines, and your existing 1/2 inch house lines will work with them. Ella recommends 3/4 inch water lines because they simply fill the tub faster. The parts are introduced in What Are the Supply Lines and Shut-Off Valves on a Walk-In Tub?, and this page stays with the sizing decision: what is already in the box, what your plumber brings, and what each pipe size means for your bath.
What Ships with the Faucet and What Your Plumber Supplies
The question usually mixes up two different things, the hoses that come with the faucet and the pipes in your walls. They are sized separately, and only one of them is your decision.
- The supply lines. These are the two braided stainless steel hoses, one hot and one cold, that carry water from your home's plumbing to the faucet. They are 3/4 inch by 5 feet, and they are included with every Ella 2-piece and 5-piece fast-fill faucet set. They travel with the faucet set, so a tub ordered without a faucet does not receive Ella supply lines.
- The shut-off valves. Each supply line ends at a shut-off valve, also called a stop valve, on the house side. These valves are not included. Your plumber supplies them and places them close to the tub.
- The house water lines. This is the pipe behind the wall or under the floor that feeds those valves. Ella recommends 3/4 inch water lines here, with the shut-off valves reachable through the front apron access panels or a wall access panel, so a future faucet or hose service does not mean shutting down the whole house.
So the 3/4 inch hoses are already taken care of. The only open question is whether the house pipe feeding them is 1/2 inch or 3/4 inch, and either one works.
The Sizes Side by Side
| Part | Size or rating in Ella's published material | What it means for you |
|---|---|---|
| Supply lines packed with the faucet set | Two, 3/4 inch by 5 foot, braided stainless steel | Included with every 2-piece and 5-piece set, nothing extra to buy |
| House water lines, recommended | 3/4 inch, with accessible shut-off valves | The faster fill |
| House water lines, existing | 1/2 inch | Will work, the tub simply fills more slowly |
| Shut-off valves | Size not listed, not included | Supplied and placed near the tub by your plumber |
| 2-piece fast-fill faucet | Up to 16 gallons per minute at 60 PSI | Rated flow with ideal plumbing |
| 5-piece fast-fill faucet | Up to 18 gallons per minute at 60 PSI | Rated flow with ideal plumbing |
| Older Ella faucets | 1/2 inch NPT lines | A 3/4 inch to 1/2 inch reducer joins old and new |
Read together, the table says the faucet and its hoses are built for high flow, and the house pipe decides how much of that flow you actually see. A home with 1/2 inch lines gets a working, comfortable tub. A home with 3/4 inch lines gets closer to the rated figures. Neither choice changes how the faucet is installed or which parts arrive with your order.
What 1/2 Inch Plumbing Means for Your Fill Time
Ella fast-fill faucets are designed for unrestricted flow, and the rated figures assume 60 PSI and ideal plumbing. Long runs of 1/2 inch house pipe feeding a faucet piped for 3/4 inch are one of the listed reasons a tub fills more slowly than the rating suggests. In real homes a fill runs about 7 to 15 minutes depending on the size of the tub and your plumbing, so a slower fill on 1/2 inch pipe is expected behavior and not a fault.
Pipe size is also only one of several things that set the pace. Before deciding to repipe, have your contractor look at the whole picture:
- House water pressure, since lower pressure than 60 PSI means a slower fill on any pipe size.
- The distance from the water heater to the tub, and whether hot water is being used elsewhere at the same time.
- Shut-off valves that are not fully open, or a kinked supply line.
- The water heater itself. A 75 gallon or larger tank is recommended, and a tankless heater should be rated 11 gallons per minute or higher.
If the tub is already installed and seems slow, Why Does My Walk-In Tub Fill So Slowly? gives the checks in order, starting with both shut-off valves. For the gallons side of the calculation, How long does it take to fill a walk-in tub? explains how occupied capacity and flow combine.
How the 3/4 Inch Lines Connect
One end of each line threads onto the faucet tail under the tub deck, and the other end threads onto the shut-off valve on the house side. Ella's 2-piece fast-fill faucet installation video shows the supply line step clearly. Before a line goes on, the installer checks that the gasket is seated correctly. The hot supply line has red markings and the cold has blue markings, and both lines have reverse threads. Each one is hand tightened and then given one quarter to one half turn with a wrench, and both lines attach the same way.
That light touch matters more than pipe size. Connections are made hand-tight and then gently snugged, never over-torqued, because over-torquing damages the internal gasket in the fitting and causes the very leak it was meant to prevent. During warranty activation your installer leak-checks the supply lines with the diverters on, so it is a good moment to ask to see the connections while the access panel is open. Later on, a slow drip at the loop of a braided line usually means the line should be replaced, not tightened further.
Older Faucets, Adapters and Replacement Lines
Current 2-piece and 5-piece fast-fill faucets use the 3/4 inch line. Older Ella faucets used 1/2 inch NPT lines, which is where most adapter questions come from. If an older faucet is being replaced with the 5-Piece Fast Fill set, the new set uses 3/4 inch supply lines. When the check valves under the tub have 1/2 inch connections, your plumber fits a 3/4 inch to 1/2 inch NPT adapter, which is a standard plumbing part. The details are in Replacing Your Walk-In Tub Faucet Set, Valves or Hand Mixer.
If you only need a new hose, Replacement Hot and Cold Faucet Supply Lines: Sizes, Threads and Where to Get Them covers the two sizes and the thread caution. Because the faucet end can be reverse-threaded, a generic store-bought line may not thread on, so confirm with a photo of the actual line before buying locally. Have your plumber shut off the supply valves before removing any line. Replacement lines are arranged through your Ella dealer or the team at (800) 480-6850, and you can open a ticket at ellasbubbles.com/support with your model, serial number, whether your faucet is the 2-piece or 5-piece, and a photo of the fitting.

Watch: Ellas Bubbles: Two Piece Fast-Fill Faucet Set Installation video with chapters and a full transcript.
Related Guides
Related Videos
