Yes. Ella's Bubbles builds custom acrylic shower pans in odd rectangular sizes, from 30 by 30 inches up to 44 inches wide by 80 inches long, and the drain can be placed left, right, center or in a custom position as long as it sits at least 9 inches from each wall. An odd size is handled as a custom build rather than a stock pan, and the size and threshold limits are set out in What is the largest custom shower base Ella makes, and which threshold heights?. This page focuses on the drain: what off center can mean, what a slab floor changes, and what to send so the pan is built to match.
What an Off-Center Drain Can and Cannot Be
On a standard Ella base the drain is not a choice you fine-tune. The standard sizes are 30 by 60, 32 by 60 and 36 by 60 inches, and each has its drain on the left or the right in a set position for that size. If your existing drain lines up with one of those positions, a standard base is the simplest answer.
A custom base is where the drain becomes adjustable. It can be placed left, right, center or in a custom position, which is what most people mean by off center. One rule holds for every custom pan:
- The drain must sit at least 9 inches from the back and side walls.
- A drain only 7 inches from the threshold edge cannot be produced, even on a custom base.
- The rule is the same for a three-wall alcove base and for a corner base.
So an off-center drain is very workable, and a drain that hugs an edge is not. If your drain line sits closer than 9 inches to a wall, it is worth knowing that before any other planning, because the pan cannot be made to meet it there.
Why a Slab Floor Makes the Drawing so Important
Ella shower bases are finished acrylic built to size at the factory. The length, the width and the drain position are all set when the pan is made, and a stock pan is not trimmed on site. That means the pan has to be right for your floor before it is built.
For a concrete slab with no access from below, the team asks you to open a ticket at ellasbubbles.com/support with a simple drawing of the space. The drawing should show the walls, the size you want and where the existing drain sits, and you should say whether the space is a three-wall alcove or a corner. The team then confirms two things: whether a base can be made to match, and what drain hardware ships with it. It is worth confirming the size before your contractor cuts the floor.
The low-threshold shower installation video on this page makes the same point from the installer's side. It covers a modular three-piece shower rather than a custom pan, but the advice carries over: dry assemble the unit in a clean open space first, check that you have received the correct drain location and that the pan is free from damage, and delay demolition of the existing bathtub area until you are confident the new unit is the correct size and condition. As the video puts it, slow is fast.
Which Odd Sizes Can Be Built
A replacement pan in an unusual size follows the same custom route as an unusual drain. Custom bases are rectangles only, and the first question for an unusual space is whether a rectangle can be drawn into it.
- Three-wall alcove base: 30 by 30 inches up to 44 inches wide by 80 inches long, specified in quarter inch increments.
- Corner base: 30 by 30 inches up to 42 by 60 inches.
- Shorter than standard: the standard bases are all 60 inches long, and a custom 58 by 30 inch base with a center drain has been produced.
- Longer than standard: a 38 by 80 inch base with a left drain is within the limits.
- Past the limits: a request such as 53 by 76 inches or 89 by 48 inches cannot be produced, even though both are rectangles.
- Not made at all: angled, curved, L-shaped or neo-angle pans.
The threshold on a custom base goes on the longer side. It comes as a 2 inch low threshold for a three-wall alcove, a 4 inch threshold for an alcove, or a 4 inch threshold on a corner base. A custom base is a low step-in pan, and a genuine roll-in threshold needs a different mold, so a wheelchair user is usually better served by one of the ready-made barrier-free sizes than by a custom pan. Other odd-layout cases are collected in Who makes custom shower pans for odd bathroom layouts?.
How to Measure the Drain Before You Ask
Good measurements are what turn a maybe into a clear answer. Take them in this order:
- Measure the width across the opening the base will fill.
- Measure the length along the back wall. On a custom base the threshold goes on the longer side.
- Find the existing drain line in the floor and measure from its center to each wall.
- Note the layout, either enclosed by three walls or in a corner against two walls, because the team places the drain and the finished edges differently for each.
- Note which side is the entry and which threshold you would like.
Measure the finished opening, and compare the drain figures with the 9 inch rule before you go further. The full walk-through, including corner bases, is in How Do You Measure a Shower Base, Including a Corner Base?.
What to Send, and What Happens Next
Send the size you want, the drain position and a simple drawing of the walls to your Ella dealer or the team at (800) 480-6850, or open a ticket at ellasbubbles.com/support. A clear request includes:
- The length and width of the finished opening.
- The distance from the center of the drain to each wall.
- Whether the space is a three-wall alcove or a corner.
- Whether the floor is a concrete slab with no access from below.
The team confirms whether that base can be made and what drain hardware ships with it. Once the pan arrives, it is finished acrylic that is ready to use once installed and does not need to be tiled over. Your contractor sets the base, connects the drain and finishes the walls around it. The plain yes and no of custom sizes is summed up in Can You Get a Custom Size Shower Tray or Shower Base?.

Watch: Step-by-Step Low-Threshold Shower Installation for Remodeling | Ella’s Bubbles with chapters and a full transcript.
Related Guides
- How Close to the Wall Can the Drain Be on a Custom Shower Base, and Can It Be Centered?
- How do you build a custom shower pan or base?
- How long does a custom Ella shower pan take to build and ship?