Support Center / Door & Seal / Which Silicone Should I Use to Reseat a Walk-In Tub Door Gasket?
Back to Door & Seal

Which Silicone Should I Use to Reseat a Walk-In Tub Door Gasket?

Ella's guidance does not name a brand or a special formula of silicone for the door gasket, and most of the time you will not need any, because the gasket is held by its fit in the channel rather than by adhesive. When a gasket has come loose or is being replaced, Ella's door seal maintenance video shows a thin bead of silicone placed in the gasket channel, never spread over the sealing face. Start with Why Does the Door Gasket Pop Out Every Time I Shut the Door? for the basic reseating steps, then use this page to decide whether silicone belongs in your repair and exactly where it goes.

Do You Need Silicone at All?

The seal on an Ella walk-in tub is a soft silicone gasket that presses into a groove running all the way around the door. Its fit in that groove is what holds it. When a section rests on the edge of the channel instead of inside it, closing the door pushes it out, and that is a seating problem, not a missing glue problem. Most gaskets that keep coming out are simply reseated and stay put.

Before reaching for a tube of anything, work through the dry fix:

  • Open the door and find where the gasket lifts out, usually near the top or at a curve.
  • If the seal looks flattened or stuck from shipping, squeeze it gently with your fingertips, pull it slightly away from the frame so it relaxes back into shape, and wipe it with rubbing alcohol.
  • Clean the groove and the frame with a common household cleaner so nothing sits under the gasket.
  • Starting at one end, press the gasket into the groove with your thumbs or a plastic spatula and work around the whole door.
  • Close and open the door several times, then fill the tub and check for leaks.

If the gasket stays seated and the door is dry, you are done and no silicone is needed. A sticky gasket does not call for silicone either, or for any lubricant. Cleaning is the answer there, as explained in My Door Seal Is Sticky. What Can I Clean or Lubricate It With?

Where the Silicone Goes, and Where It Never Goes

Ella's maintenance video describes silicone as a step for the rare instance when a door seal has become loose or damaged and has to be removed and put back or replaced. The sources describe the product simply as silicone, and the article on resealing the door handle screws calls silicone sealant a hardware-store item. What matters far more than the label on the tube is the placement and the waiting time.

SituationWhere the silicone goesWaiting timeWhat it means for you
Gasket pops out but is otherwise soundNoneNoneClean the groove and press the gasket fully back in
Loose or damaged seal removed and replaced, channel method shown in the videoA thin bead placed into the gasket channelLet it set up for 20 minutes before reinserting the gasket, then wait 24 hours for it to dryThe bead secures the gasket from behind, out of the sealing path
Inward swing doorRoll the gasket away from the frame and run a bead down the corner where the gasket meets the frame, with a bead on the other side of the gasket if necessaryWait 24 hours to dryThe gasket stays on the door while you work
Sealing face of the gasketNeverNot applicableCaulk or silicone on the face keeps the gasket from sealing
Water weeping at the door handle screwsInto each screw hole and under each screw headThe full cure time stated by the sealant manufacturerThis is a screw hole leak, not a gasket problem

What the table means in practice: silicone is only ever a backing for the gasket, hidden in the channel or tucked into the corner where the gasket meets the frame. The face of the gasket, the part that compresses against the frame when you lock the door, must stay bare and clean. A door that still leaks after leveling and reseating is not improved by a layer of silicone or caulk over the seal. That seal is replaced with a model specific part instead.

How to Apply the Bead, Step by Step

  1. Drain the tub and dry the door, the gasket and the channel.
  2. Clean the channel and the frame so the gasket and the bead sit on a clean surface.
  3. For the channel method, remove the loose section of gasket and place a thin bead of silicone into the gasket channel. Keep it thin. The gasket still has to seat fully in the groove.
  4. Allow the silicone to set up for 20 minutes before reinserting the gasket.
  5. Press the gasket back into the groove with your thumbs or a plastic spatula until it is fully seated along its whole length.
  6. For an inward swing door, roll the gasket away from the frame and run a bead of silicone down the corner where the gasket meets the frame. Add a bead to the other side of the gasket only if it is needed.
  7. Wait 24 hours for the silicone to dry before the tub sees water.
  8. Fill the tub, check the door edge all the way around, and then leave the door slightly open between baths so the gasket is not compressed for long periods.

What the Two Videos Show

The door seal maintenance video on this page shows regular cleaning of the seal and frame, then the silicone step: the thin bead in the gasket channel, the 20 minute set time, the 24 hour drying time, and the inward swing method of rolling the gasket away from the frame. It closes with the advice to leave the door open slightly when the tub is not in use.

The seal installation video shows a full gasket replacement. Adhesive remover is sprayed onto the gasket there, and it is worth knowing why. It is used to help the gasket slide more easily into the door channel, not to glue anything. The video also shows a spatula pressing the gasket into the groove, four V-shaped relief cuts where the gasket bends around the outer curves, straight vertical cuts at the inner curves, and a small angled cut at the end so the tip slightly overlaps while sitting fully in the groove.

When Silicone Is the Wrong Fix

Water at the door does not automatically mean the gasket needs to be secured or sealed. The number one cause of a door leak is leveling, because a leveling leg that has lost contact with the floor lets the frame warp so the door no longer meets the seal evenly. Why Does My Walk-In Tub Door Leak at the Bottom? walks through that check, along with the handle lock nut adjustment for a door that no longer pulls tight.

If the water appears at or just below the handle while the rest of the door edge stays dry, the silicone belongs on the handle screws, not the gasket. That repair is covered in Water Leaking From the Door Handle Screws: Reseal the Screws Before Replacing the Door Seal.

A gasket that will not stay seated after reseating, or that is torn or damaged, is replaced. The door seal is covered with the door under the Lifetime Limited Warranty, and each door uses its own seal size, so the replacement is matched to your model and serial number. Open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your serial number, clear photos of the seal and the leak point, and a note on whether all the leveling legs touch the floor. Ella does not send technicians. The part ships under the warranty, and you or a local licensed plumber fit it. For background on how the seal works, see What Is the Door Seal on a Walk-In Tub?

Video

Watch: How To Install a Walk-In Tub Door Seal (Step-By-Step) with chapters and a full transcript.

Video

Common Questions

Does Ella recommend a specific brand of silicone for the door gasket?
No specific brand or formula is named in Ella's guidance. The maintenance video refers simply to a thin bead of silicone, and silicone sealant is described as a hardware-store item. Placement and drying time are what the guidance focuses on.
Can I put silicone over the gasket to stop a door leak?
No. Do not spread caulk or silicone over the sealing face of the gasket, because that face has to compress cleanly against the frame. A seal that still leaks after leveling and reseating is replaced with a model specific part.
How long should the silicone dry before I use the tub?
For the channel method, let the bead set up for 20 minutes before reinserting the gasket, then wait 24 hours for the silicone to dry. For the inward swing method, wait 24 hours as well. Fill the tub and check for leaks only after that time.
Is the door gasket normally glued into its channel?
No. The gasket is a silicone strip that presses into a groove around the door and is held by its fit rather than by adhesive. The silicone bead is a step for the rare case when a seal has come loose or is being replaced.
Why is adhesive remover sprayed on the gasket in the installation video?
It is sprayed on to help the gasket slide more easily into the door channel during a replacement. It is not acting as a glue. The gasket is then pressed into the groove with a spatula until it is fully seated.
What should I do if the gasket keeps popping out after reseating?
A gasket that will not stay seated after reseating is replaced. Open a ticket at ellasbubbles.com/support or call (800) 480-6850 with your serial number and clear photos of the seal. The door seal is covered under the Lifetime Limited Warranty and the replacement is matched to your model.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket