Support Center / Showers, Panels & Accessories / Does a Three Panel Wall Kit Need a Glue-Up Flange Over Existing Tile?
Back to Showers, Panels & Accessories

Does a Three Panel Wall Kit Need a Glue-Up Flange Over Existing Tile?

Yes. A three panel wall kit still needs the glue-up flange when it goes over existing tile, because the flange seals the joint where the tub or shower base edge meets the wall, and that is a separate matter from what the wall itself is made of. The old tile can stay as the surface the panels glue to, but it does not replace the thin waterproof strip described in What Is a Tile Flange on a Walk-In Tub?, which sends water running down the wall back into the fixture instead of behind it.

Why Existing Tile Does Not Take the Place of the Flange

Ella shells have a flat deck edge with no integral tile lip, and that is by design. On a fixture with a molded lip, the lip rises behind the wall finish and turns water back. On an Ella walk-in tub, that job is done by a strip added at installation: a thin, rustproof, waterproof band glued to the tub edge with 100 percent silicone so that it overlaps the edge by about 2 inches. The wall finish, whether tile or wall panels, then comes down over the flange and onto the deck, and every joint is sealed with silicone.

Existing tile covers the wall, but it stops at the wall. It does nothing for the joint between the wall and the deck, and that joint is exactly where a new tub or base meets an old surface. When acrylic panels are glued over the tile, their bottom edge lands at that same joint. With the flange bonded to the edge first, the panels overlap it, so water running down the wall is carried back into the tub or base. Ella's flexible flange also follows the small movement between the fixture and the wall that a rigid plastic lip cannot. If the missing lip surprised you or your installer, My Tub Has No Tile Lip. Which Flange Do I Use? explains why the tub is built that way.

What the Three Panel Kit Needs from the Old Tile

The Ella acrylic three panel surround is one back panel 60 inches wide and two side panels 40 inches wide, offered in a 98 or 105 inch height. The panels are a 0.118 inch thick ABS and PMMA composite with a glossy acrylic surface. The kit glues directly over existing tile or drywall with no demolition, and the panels trim on site for a close fit. The panels are dry-fitted first, set with 100 percent silicone, and then braced or taped for 24 hours while the silicone cures.

Because the panels are glued, the wall behind them is part of the system. Before anything goes up over old tile, have your installer confirm these points:

  • The tile is sound. Existing wall tile that is sound and properly sealed can stay. Loose or uneven tile is a reason to stop and have your installer confirm the wall before anything is glued to it, and a panel must never be installed over a damaged wall.
  • The surface is clean and dry. A glued panel depends on a surface that is sound, clean, dry and sealed.
  • The walls are plumb and square within 1/8 inch. Panels hide the wall behind them, but they do not correct it. Corner seams open up when the back wall leans or the corners are not square.
  • The room is above 65 degrees when the panels go up.
  • The alcove matches the kit. The acrylic kit is molded to a fixed footprint, so confirm the alcove depth, width and ceiling height against the kit on your order.

If the wall behind the tile turns out to need repair and you end up on bare board instead, What primer or sealer goes on drywall before acrylic shower walls? lists the approved substrates and how each one is sealed.

The Order of Work over Existing Tile

The sequence matters more than any single step, because the flange has to be in place before the panels come down over it.

  1. Set and level the tub or base with every leg bearing on the floor.
  2. Water test it before any wall is finished. Fixing a leak behind finished walls is far more disruptive than finding it now.
  3. Clean the edge of the tub or base with the alcohol tissues supplied in the flange kit.
  4. Bond the flange with 100 percent silicone so it overlaps the edge by about 2 inches. The strip is reversible. On a fixture with no built-in flange, which includes every Ella walk-in tub, the red surface faces you.
  5. Dry-fit the three panels, trim them as needed, then run them down over the flange and onto the deck.
  6. Silicone every joint in the wet area, including where an extension panel meets the tub and where an end panel meets the wall.

The full panel sequence, from wall preparation to the last bead of silicone, is in How Do You Install a Three-Piece or Glue-Up Shower Surround?. The instructions packed with your kit govern wherever they differ from a general description.

Choosing and Fitting the Flange Kit

Ella's own Flexible Glue-Up Tile Flange kit, listed as FlangeBand, is a 124 inch strip of 4 inch wide flexible membrane with a 1 1/4 inch adhesive strip, a spreading spatula, an alignment guide and alcohol wipes. The 124 inch kit suits most Ella tubs in a standard three-wall 60 inch alcove, and longer strips are listed for larger models such as the Big4One, TransferXXL, LayDown72, Escape and Big4Two. To check the length, measure the total run of edge that meets a wall, back plus each end, at deck height.

A few practical points save time on install day:

  • No Ella walk-in tub ships with a tile flange. The flange ships separately by parcel carrier, not in the crate with the tub, so it is not missing if it is not in the crate on delivery day.
  • When you request one through where you purchased or the team at (800) 480-6850, include your model so the right length ships. Support records the flange under the part code EB-FLANGE.
  • For a shower base the same flange approach applies, and the flexible strip can go on after the base is set.
  • The ShaK is the one exception to note. It is not designed to be tiled in directly, so talk with technical support before planning wall finishes around a ShaK.

What the Videos Show

The flange installation video opens with the kit contents: the roll of flexible flange, the alcohol surface cleaning cloths, the custom spatula tool and the strip alignment card. It explains that the flange is a durable, waterproof adhesive fabric with a siliconized membrane that chemically bonds to the applied silicone sealant, which is what keeps the seal tight through general expansion, contraction and routine floor settling. It then shows the first step, marking the strip position on the walls with the alignment card so the strip is aligned correctly, including a second marking method for tighter three-wall enclosures where the fixture is not slid into its working position first. The accessories video shows the same flange in use around a shower base and notes that it is strongly recommended for the installation of Ella tubs.

If your walls are already partly finished, or you are not sure which flange length fits, open a ticket at ellasbubbles.com/support with your model, a sketch of the alcove with wall lengths in inches and a photo of the edge where it meets the wall. Your Ella dealer or the team at (800) 480-6850 will confirm the kit and how to place it.

Video
Watch: Installing a Glue-Up Tile Flange: Step-by-Step | Ella’s Bubbles with chapters and a full transcript.
Video

Watch: Walk-In Tub Accessories to Enhance Your Experience | Ella's Bubbles with chapters and a full transcript.

Common Questions

Can the three panel kit be glued directly over old tile?
Yes. The acrylic three panel surround glues directly over existing tile or drywall with no demolition, and the panels trim on site for a close fit. The tile has to be sound and properly sealed, and your installer confirms its condition before anything is glued to it.
Why do I need a flange if the wall is already tiled?
The flange seals the joint where the tub or base edge meets the wall, which is separate from the wall surface. Ella shells have a flat deck edge with no integral tile lip, so the strip is the barrier that sends water back into the fixture instead of behind it.
Which side of the reversible flange strip faces out?
On a fixture with no built-in flange, the red surface of the reversible strip faces you. That includes every Ella walk-in tub, because no Ella walk-in tub has an integral tile lip.
Does the flange go on before or after the panels?
The flange goes on first. Set and level the tub or base, water test it, clean the edge, and bond the flange with 100 percent silicone. Then the panels run down over the flange and onto the deck, and every joint in the wet area is sealed with silicone.
What should I do if the old tile is loose?
Stop and have your installer confirm the wall before anything is glued to it. A glued panel depends on a surface that is sound, clean, dry and sealed, and a panel must never be installed over a damaged wall.
Does the flange kit arrive in the crate with the tub?
No. The flange ships separately by parcel carrier, so it will not be in the crate on delivery day. When you request one, include your model so the right length ships.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket