Support Center / Installation & Leveling / How Do You Seal the Gap Between a Walk-In Tub and the Wall?
Back to Installation & Leveling

How Do You Seal the Gap Between a Walk-In Tub and the Wall?

The gap between an Ella walk-in tub and the wall is sealed in three layers: a tile flange that overlaps the tub edge, a wall finish that overlaps the flange, and a bead of 100 percent silicone at every joint. Ella tubs have a flat deck edge with no molded tile lip, so the flange is what carries splash water back into the tub instead of down the wall line. If you are already seeing water at the wall, start with Why Does My Tub Leak at the Corners or Wall When Filled? This page explains how the seal is built so it stays dry from day one.

Why There Is a Gap to Seal in the First Place

Many standard bathtubs have a raised lip molded into the edge that tucks behind the wall finish. Ella walk-in tubs are different. The deck edge is flat, so there is nothing built into the tub to stop water that runs down the wall from slipping behind the deck. That is by design, and it is why the wall line is finished on site.

A correct wall line has three parts working together:

  • The flange overlaps the tub edge. A flange strip is bonded to the tub edge with 100 percent silicone.
  • The wall finish overlaps the flange. The tile or wall panel comes down over the flange, so water running down the wall lands on the deck.
  • Every joint is siliconed. The visible joints are closed with a bead of 100 percent silicone.

If any one of those layers is missing, splash water runs down the wall line and shows up at the corners. The usual causes are no tile flange at all, a flange that does not overlap the tub edge, tile or panels that stop above the flange instead of overlapping it, or corners that were left uncaulked or caulked with something other than silicone.

How the Glue-Up Tile Flange Goes on

Ella's glue-up tile flange is the part that bridges the tub edge and the wall, and the video on this page shows the installation. The kit comes with a roll of Sealux to fit your requirements, alcohol surface cleaning cloths, a custom spatula tool and a strip alignment card. Sealux is also offered in bulk form for contractors.

The video explains why the flange holds. It is a flexible flange made of a durable, waterproof adhesive fabric and a siliconized membrane. When 100 percent silicone is applied to the silicone-based strip, the two bond chemically and create a tight, durable waterproof seal. Because the flange is flexible, the seal is designed to stay waterproof through general expansion and contraction and through routine floor settling.

The first step shown is marking the strip position on the walls so the flange ends up aligned correctly. The video demonstrates two alignment methods:

  1. With the tub in place. Set the tub temporarily in its working position. Rest the alignment card on the ledge against the wall and mark each wall at least twice at the height the card gives you. Mark the wall where the tub ends as well. Then move the tub out, draw horizontal lines through the upper marks and draw vertical lines just outside the tub end marks.
  2. For tighter three-wall alcoves. The lines can be marked without sliding the tub into its working position, by calculating the height of the strip's upper edge from the height the ledge will sit above the floor after installation.

Either way, the goal is the same: the strip sits in a straight, level line that the wall finish can come down over.

Where the Silicone Goes

Once the flange and wall finish are in place, run a bead of 100 percent silicone at every joint. It is easy to seal the long back wall and miss the short joints, so work through the full list:

  • Tub to wall along all three sides.
  • Each corner.
  • The extension panel to tub line.
  • The end panel to wall line.

If your tub has a glass screen, its wall channel gets the same care. A thin bead of silicone between the channel and the wall finishes that seal, and the bottom gasket should brush the tub deck lightly and evenly with the rubber lip angled inward toward the tub. The checks for that are in Why Does My Shower Screen Gasket Have a Gap and Spray Water?

When the Gap Is Wider Than a Caulk Joint

Silicone closes a joint. It is not meant to fill a space left because the tub is shorter than the alcove. For that, Ella offers extension panels that can be cut down to size to close the space cleanly, which lets a standard tub size fit an alcove that is slightly larger than the tub. The size choices are covered in Walk-In Tub and Shower Base Sizes and How to Measure for Fit.

The opposite situation comes up too. When an end panel is a fraction of an inch too long for the opening between the finished wall and the front apron, it can be tempting to pull the tub away from the wall to make room. That is the wrong fix, because it leaves a gap between the wall and the end of the tub. The fix support recommends is trimming the panel on the edge that sits against the wall, then caulking the wall joint. The steps are in End Panel Too Long for the Opening: Trimming It to Fit.

Checks That Keep the Seal Working

A good wall seal depends on the tub underneath it, so a few checks belong with the job:

  • Level first. Confirm the tub is level with every leg bearing. An unlevel frame opens gaps at the wall and at the door together.
  • Water test before the walls are closed. On a new installation, fill and hold the tub with the access panels open before the wall finish goes on.
  • Test the finished wall line. Dry everything, fill the tub with the door closed and let it stand. If the corners stay dry until you splash or use the hand shower, any water you see is coming over the deck edge at the wall, and the wall line needs attention.
  • Rule out water from under the tub. If water appears on the floor while you bathe, open the access panels and trace it there instead. A union, an air fitting, a button gasket or the drain elbow can send water to the floor corners and look like a wall leak.

If the wall line is sealed and water still shows at the corners, open a ticket at ellasbubbles.com/support with your model and serial number, a photo of the corner where water appears and a photo behind the access panel. Your Ella dealer or the team at (800) 480-6850 can also help.

Video

Watch: Installing a Glue-Up Tile Flange: Step-by-Step | Ella’s Bubbles with chapters and a full transcript.

Common Questions

Do Ella walk-in tubs have a built-in tile lip?
No. Ella tubs have a flat deck edge with no molded tile lip. A tile flange that overlaps the tub edge does that job, with the wall finish overlapping the flange.
What kind of caulk should I use between the tub and wall?
Use 100 percent silicone. It goes at every joint, and it is also what bonds the flange strip to the tub edge.
What comes in the Ella glue-up tile flange kit?
The kit comes with a roll of Sealux to fit your requirements, alcohol surface cleaning cloths, a custom spatula tool and a strip alignment card. Sealux is also offered in bulk form for contractors.
Which joints around the tub need a bead of silicone?
Seal the tub to the wall along all three sides and at each corner. Then seal the extension panel to tub line and the end panel to wall line.
How do I close a wide gap between the tub and the wall?
A space left because the tub is shorter than the alcove is closed with an extension panel, which can be cut down to size. Silicone then seals the joints around it.
Should I move the tub out to make the end panel fit?
No, because that leaves a gap between the wall and the end of the tub. Trim the end panel on the wall-side edge instead, then caulk the wall joint.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket