Support Center / Plumbing & Electrical / How Do You Rough In the Drain for an Ella Shower Base?
Back to Plumbing & Electrical

How Do You Rough In the Drain for an Ella Shower Base?

You rough in a shower drain by working from the Specification drawing for your exact Ella base and drain position, which gives the distance from the back wall and from the side wall to the center of the drain. Your plumber sets the waste pipe at that point, dry fits the base to confirm the two line up, and only then makes the final connection. The measuring method is explained in Shower Drain Rough-In: How Far the Drain Sits From the Back Wall and Side Wall, and this page walks through the whole job in the order it happens on site.

Start with the Drawing, Because the Drain Cannot Move

The most helpful thing to know before any pipe is cut is that the drain opening on an Ella shower is molded into the base at the factory. It is part of the floor of the base, so it cannot be shifted on site, and the floor plumbing has to come to the base instead of the other way around. That is why the rough-in always begins with paper and a tape measure.

Every Ella shower base has a dimensioned Specification drawing. It shows the outside dimensions of the base, the threshold, and the drain location measured to the center of the drain opening. The drawing is the authoritative source, and it is the same document the support team reads from when someone asks for a drain measurement. If you do not have it, your Ella dealer or the team at (800) 480-6850 can supply the drawing for your model.

There is no single rough-in figure that fits every base. As two examples from the published drawings, one right-drain base lists the drain center 15 1/2 inches from the back wall and 9 1/2 inches from the front, while one center-drain base places it 19 inches from the back wall and 24 inches from the side wall. A left drain, a right drain and a center drain are each a different set of numbers, so always name the drain position along with the model when you ask for a measurement.

Know Which Drain Positions Your Base Offers

How much freedom you have depends on the base family, and it is worth settling this before the plumber arrives:

  • Standard acrylic bases. The 30 by 60, 32 by 60 and 36 by 60 inch bases each come with a left or right drain in a set position, so the handing is chosen with the order.
  • Stalls and other molded bases. Most Ella stalls and bases are center drain, and some bases are molded with a left-hand drain only. A model built one way is only available that way, as explained in Can I Choose a Left, Right, or Center Drain on an Ella Shower?
  • Custom bases. A custom base can have the drain left, right or center, as long as it sits at least 9 inches from each wall.
  • The reversible SMC base. The SMC 1 inch low-profile reversible base covers both handings with one part. Set it one way and the linear drain runs along the left end, set it the other way and it runs along the right end, so the choice is made on the floor at installation.

Zero threshold bases are also available and sit flush with the surrounding floor. Your Ella dealer or the team at (800) 480-6850 can confirm which threshold style suits your bathroom and how it fits with your existing plumbing rough-in.

Measure the Existing Drain Against the Drawing

In a remodel there is usually a drain line in the floor already, and the first job is to see whether it can stay where it is.

  1. Get the Specification drawing for your exact model and drain position.
  2. Locate the existing drain pipe and have your plumber measure from the center of the pipe to the wall framing behind it and to the framing on the nearer side wall.
  3. Measure to the studs where possible. The base sits against the framing once the finish materials are removed, so a measurement taken to old tile or drywall will not match the drawing.
  4. Compare the two measurements with the back-wall and side-wall figures on the drawing.
  5. If the numbers match within the tolerance your plumber is comfortable with, the base can be set over the existing line. If they do not, decide with your plumber whether to move the drain line or change the base.

Do this comparison before the order is placed. A drain that does not line up is usually discovered only when the base is set on the floor, and that is the hardest point in the project to change course.

Open the Floor, Then Dry Fit Before You Commit

Once the location is confirmed, the floor is prepared for the waste pipe. For the SMC low-profile bases, the published guide calls for a 5 by 5 inch opening in the floor for a 2 inch PVC waste pipe, positioned according to the product rough-in specifications for the exact drain location. For any other base, follow the installation manual and drawing for that model instead of borrowing a figure from a different one.

The published guide also asks for a dry fit before the floor is cut. Set the base in the pocket in its final layout and confirm the drain body lines up with the mark on the rough floor. On the reversible SMC base this step matters twice over, because the floor opening has to match the end you chose for the linear drain. The practical order is to decide which end the drain will face, usually the end nearest the existing waste line or the end that suits the entry, read the rough-in specification for that layout, mark the floor, and dry fit. The details for that base are in Which end can the linear drain face on the reversible SMC shower base?

What Arrives in the Box and What Your Plumber Brings

An Ella shower kit ships with the shower stall, the grab bar set listed for that kit, and the drain. The drain that ships with the kit is connected to the house waste line by your plumber, who also supplies the rough-in piping and fittings. Ella does not send technicians, so the drain connection is always made by your local licensed plumber.

It helps to plan the wall plumbing during the same visit. The kit does not include a mixing valve, valve trim or supply plumbing, and the wall arrives solid with no valve cutout, so your plumber selects the valve and cuts the openings on site. The complete list is in What Comes in the Box With an Ella Shower Kit, and What You Still Need to Buy.

If the Drain Does Not Line Up

You have good options when the existing line and the drawing disagree:

  • Relocate the drain line. A licensed plumber can tell you whether your floor construction allows the trap to be moved to match the base. This is routine in a remodel when the floor is open.
  • Choose a different base. Another size may have a drain location that fits the line you already have.
  • Ask about a custom base. When moving the drain is not practical, a custom-size base can have the drain positioned to suit your line, within the rule of at least 9 inches from each wall.

Common Questions

Where do I find the drain rough-in measurement for my shower base?
It is on the Specification drawing for your exact model and drain position, shown as the distance to the center of the drain opening. Your Ella dealer or the team at (800) 480-6850 can supply the drawing if you do not have it.
Can the drain on an Ella shower base be moved?
No. The drain opening is molded into the base at the factory and is fixed for each model. If it does not match your floor, the choices are a different base, a custom-size base, or having your plumber relocate the rough-in.
Should the plumber measure to the finished wall or the studs?
Measure to the studs where possible. The base sits against the framing once the finish materials are removed, so the framing is the reference that matches the drawing.
How big is the floor opening for the SMC shower base drain?
The published guide for the SMC low-profile bases calls for a 5 by 5 inch opening in the floor for a 2 inch PVC waste pipe. It is positioned according to the product rough-in specifications, and the guide asks for a dry fit before the floor is cut.
Does the Ella shower kit include the drain and the piping?
The kit ships with the drain. Your plumber connects it to the house waste line and supplies the rough-in piping and fittings.
How close to a wall can a custom base drain sit?
A custom base can have the drain on the left, on the right or in the center. It needs to sit at least 9 inches from each wall.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket