Support Center / Walk-In Tub Models / Which drop-in bathtubs make installation easier in a manufactured home?
Back to Walk-In Tub Models

Which drop-in bathtubs make installation easier in a manufactured home?

Ella's Bubbles mainly makes walk-in tubs rather than standard drop-in tubs, so there is not a drop-in model to recommend. For manufactured homes the team recommends two compact walk-in tubs for single-wide homes, the Mobile 26x45 and the Front Entry 32x40, because both fit a short space and pass the narrow doorways common in manufactured housing. Which Walk-In Bathtubs Fit Single-Wide and Double-Wide Manufactured Homes? compares the full list by home type, and this page looks at the question the way a drop-in shopper asks it: what actually makes the installation simpler.

What a Simple Installation Really Depends on

People search for a drop-in tub because they want a bathtub that goes in without a struggle. In a manufactured home the struggle is rarely the tub style. Usually the hardest part is getting the tub through the doors and the hallway and into the bathroom. An Ella remodel in a manufactured home is a walk-in conversion, and the tub is the same one that goes into any house. What changes is the planning.

Three facts shape that planning:

  • You need a door opening larger than 26 inches for the narrowest tub in the Ella line, and every other model needs more.
  • Ella tubs ship fully assembled and cannot be taken apart to fit.
  • Manufactured, prefab and modular homes usually have doors wide enough. RVs, campers and small trailers often do not.

So the tub that simplifies your installation is the one that clears your route with room to spare. Walk the whole path and write down each figure:

  1. The exterior door the tub will come through.
  2. Every interior doorway between that door and the bathroom, including the bathroom door.
  3. The hallway width, which matters as much as the doorways.
  4. Each corner and turn, since a tub that clears a doorway still has to swing around the bend after it.

Each spec sheet prints two sets of numbers. Shipping size is the crated dimension, and it applies from the curb to wherever the crate is opened. Actual size is the tub itself, and it applies to every opening the bare tub passes after that. Where the crate will not clear, the tub is uncrated outside and carried in by its frame, so the actual width becomes the figure that matters at your tightest doorway, and the passage must be wider than it. Can You Put a Walk-In Tub in a Mobile or Manufactured Home? follows that route from the front door to the first bath.

The Compact Models to Compare Instead of a Drop-In

The table uses only published actual and shipping sizes. Never plan from the rounded model name, and confirm the figures on the current spec sheet for the model you choose.

ModelActual sizeShipping sizeWhat it means in a manufactured home
Front Entry 32x4032 inches wide, 40 inches long, 40 inches highnot listedShortest tub in the line; the end door lets it slide into a 40 inch opening, with two removable side panels for corner or single-wall placement
Mobile 26x4526 inches wide, 45 inches long, 39 1/4 inches highnot listedNarrowest tub in the line; no extension panel, so plan on a 45 inch space or a corner
Flow 28x4828 x 48 x 36.5 inches32 x 54 x 49 inchesCompact choice with a little more length than the Mobile
Petite 27.5x5227.5 x 52 x 35 inches31 x 57 x 47 inchesA 52 inch tub with the most room to spare at a doorway
Elite 30x5230 x 52 x 35 inchesnot listedThe common footprint, for a home with wider doorways and hallways
Capri 30x5230 x 52 inches, height not listednot listedCompact outward-swing door model that needs clearance in front of the tub
Monaco32 inches wide, length not listednot listedNeeds a wider passage and a wider opening

What the differences mean: the two models the team recommends for single-wide homes sit at the top of the table for a reason. The Mobile is the narrowest, so it is the one most likely to pass a tight doorway. The Front Entry is the shortest, and because its door is on the end and not on the side, it can slide into a space only 40 inches long. The Flow is the third compact choice the team suggests. The Elite, Petite and Capri are also common starting points, and they open up once your doorways and hallway allow. Compare the actual width of each one with your narrowest opening, then compare the actual length with the bathroom space measured wall to wall. If your current bathroom has a shower stall and not a tub, Can a walk-in tub be installed where my walk-in shower is now? covers that swap.

Floor, Plumbing and Power Come Before the Order

Manufactured homes have lighter floor framing, so have a contractor who knows manufactured housing check the floor, the plumbing and the power before you order. This is the step that keeps the installation simple on the day, because nothing has to be discovered after the tub arrives.

A walk-in tub places three loads on the floor at once: the tub, the water and the bather. Ella's owner's manuals require a level subfloor that can support the total weight of all three and that meets local code. Water weighs about 8.34 pounds per gallon, so the water is usually the largest share of the load. As one example, the Front Entry weighs 200 pounds empty and holds 70 gallons unoccupied. Inspectors start from the International Residential Code minimum of 40 pounds per square foot for living areas, but a tub is a concentrated load on a small footprint, so joist size, span, spacing and condition all matter. Mobile home floors vary widely, and local mobile-home guidelines may apply.

Beyond the floor, the installation needs the same things as any walk-in tub: a working drain and water supply, and dedicated GFCI-protected power. Are walk-in tubs a good option for mobile homes? goes through each of those checks.

Who Does the Work and Where the Tub Comes from

Every Ella walk-in tub is assembled, jetted and tested to order in Chicago and ships fully assembled. Ella does not install. A local licensed plumber and electrician, or a general contractor who knows manufactured housing, does the work, and Ella's technical support is there for them with manuals and live video help.

There is no separate supplier for manufactured housing. The tubs reach manufactured homes and remodel projects across the country through a nationwide network of authorized resellers, so the place to start is your Ella dealer or the team at (800) 480-6850. Which distributor sells Ella walk-in tubs for manufactured homes and remodels? explains how that network works. Have your doorway, hallway and bathroom measurements ready when you call, along with your contractor's notes on the floor, and the team can match them to a model.

Video
Video
Video

Common Questions

Does Ella's Bubbles make a drop-in bathtub for manufactured homes?
No. Ella mainly makes walk-in tubs rather than standard drop-in tubs, so there is no drop-in model to recommend. An Ella remodel in a manufactured home is a walk-in conversion using one of the compact models.
Which Ella tubs does the team recommend for a single-wide home?
The team recommends the Mobile 26x45 and the Front Entry 32x40 for single-wide homes. Both fit a short space and pass the narrow doorways common in manufactured housing. The Elite, Petite, Capri and Flow are also common starting points.
How wide does my doorway need to be for the tub?
You need a door opening larger than 26 inches for the narrowest tub in the Ella line, and every other model needs more. Compare each model's shipping size and actual width with every doorway and hallway on the way in.
Can the tub be taken apart to fit a narrow hallway?
No. Ella tubs ship fully assembled and cannot be taken apart to fit. Where the crate will not clear, the tub is uncrated outside and carried in by its frame, so the actual width is the figure that matters at your tightest doorway.
Does the floor of a manufactured home need to be checked first?
Yes. Manufactured homes have lighter floor framing, and the floor carries the tub, the water and the bather at once. Have a contractor who knows manufactured housing check the floor, the plumbing and the power before you order.
Who installs an Ella tub in a manufactured home?
Ella does not install. A local licensed plumber and electrician, or a general contractor who knows manufactured housing, does the work. Ella's technical support helps them with manuals and live video help.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket