Support Center / Maintenance & Cleaning / Can You Use Bath Salts or Epsom Salt in a Jetted Tub?
Back to Maintenance & Cleaning

Can You Use Bath Salts or Epsom Salt in a Jetted Tub?

Yes, you can use plain Epsom salt in a jetted Ella walk-in tub, as long as it is fully dissolved before it goes into the bath and the tub is drained and rinsed afterward. Scented or colored bath salts are a different product and are not recommended, because the dyes and fragrance oils they carry can affect the jet system. The full product list is in Can I Use Epsom Salts, Bath Bombs or Bubble Bath in My Walk-In Tub?, and this page stays with salts alone: which kind, in what order, and how to look after the tub when the soak is over.

Why the Kind of Salt Matters in a Jetted Tub

A jetted Ella tub draws bath water in through the intake, pushes it through the pump and the in-line heater, and sends it back out through the jets. Anything in the water makes that trip too. That one fact explains every rule on this page.

Plain Epsom salt dissolves completely, and fully dissolved Epsom salt will not harm the pumps, the heater or the jets. The only risk with plain salt is a crystal that has not dissolved yet, because an undissolved salt crystal can lodge in a jet.

Scented and colored bath salts bring more than salt into the water. Depending on the product, they can carry dye, fragrance oils, glitter and floral bits. Dyes and fragrance oils can affect the jet system, solids can clog the jets, and oils coat the inside of the pumps and lines, where they are hard to flush back out. That is why Ella's guidance places scented or colored bath salts in the not recommended group, alongside the products covered in Is Bubble Bath, Bath Bombs or Bath Oil OK in a Jetted Walk-In Tub?

Here is how the salt products sort out:

  • Plain Epsom salt: yes, with care. Dissolve it completely, drain when you are finished, and rinse the tub and every chrome fitting.
  • Scented or colored bath salts: not recommended. If you choose to use them anyway, use them sparingly, dissolve them fully, and rinse thoroughly.
  • Bath beads and fragrance beads: not recommended in a jetted tub. They can lodge in the pumps and jets, and damage caused that way falls outside the warranty.

If your tub is a soaking-only model with no pumps, the rules are much more relaxed, because there is no jet system for the water to travel through.

The Right Way to Add Epsom Salt

Two simple habits make an Epsom salt soak easy on the tub: dissolve first, and rinse last. The team also shares one best-practice tip about timing, which is to enjoy your therapy first and add the salt afterward.

  1. Run your hydro, air or microbubble therapy first. Dissolved salts will not harm the jetting system, but keeping them out of the running pumps is the team's best-practice advice.
  2. While you enjoy the massage, or just before, dissolve the Epsom salt completely in a cup or bowl of warm water. No crystals should be visible.
  3. Once the systems are finished, add the dissolved salt to the bath and settle in for a still soak.
  4. Drain the tub when you are finished soaking, instead of letting the salt water sit.
  5. Rinse the whole tub with the hand shower and wash the residue down the drain.

Pouring dry salt straight into the bath is the step to avoid. The crystals take time to dissolve, and until they do, they can reach the jets.

Rinsing the Tub and Protecting the Chrome

Salt is gentle on the jets when it is dissolved, but it is not kind to metal finishes when it is left to dry. Salt residue that dries on chrome can eat at the finish and leave spots, and over time it can discolor the trim. The rinse after a salt soak is what prevents that.

When you rinse, give special attention to:

  • the jet covers
  • the drain plugs
  • the handles and the faucet
  • any other chrome trim, along with the stainless threshold

Then wipe the chrome and stainless dry. Wiping these surfaces after every salt soak is what keeps them bright.

If you have already noticed marks near the drain or the threshold, they may not be rust at all. Salt water that dries on chrome or stainless leaves spots that look very much like rust. Wipe the area with mild soap and water on a soft cloth, then dry it, and do not use anything abrasive. If the spots lift, they were deposits. If they stay, do not scrub harder. The next steps are laid out in Why Are There Rust Spots on My Tub's Stainless Threshold or Drain?

If Scented Salts or Other Additives Have Already Gone in

One bath with a scented salt is not a reason to worry, and there is a simple routine for clearing the system. Rinse the tub well, then run the vinegar flush that Ella recommends once a month:

  1. Combine 2 cups of white vinegar with 2 cups of water.
  2. Fill the tub with water to 1 inch above the highest jets.
  3. Add the mixture and run the tub for 10 minutes.
  4. Drain the tub.

If you decide to keep using oils, beads or fragrance products now and then, plan on more frequent vinegar flushes and a thorough rinse each time. Bath bombs are the one product Ella asks you to leave out entirely, for the reasons explained in Can I safely use bath bombs in a jetted walk-in tub?

For a scented bath without the worry, the simplest choice is the one that is always fine. Everyday soaps, shampoos and body wash rinse away with the bath water and cause no trouble, and any ordinary brand works. Rinse well afterward so nothing is left in the jets.

When to Reach Out for Help

If spots on the chrome or stainless do not wipe away with mild soap and water, or the drain or trim looks pitted or corroded, contact your Ella dealer or the team at (800) 480-6850, or open a request at ellasbubbles.com/support. It helps to include:

  • your model and serial number
  • close photos of the affected metal, taken in good light
  • a note on which bath products and cleaners have been used in the tub

Photos are how the team confirms what they are looking at, so a few clear pictures go a long way.

Common Questions

Will Epsom salt damage the jets or pump in my tub?
No, fully dissolved Epsom salt will not harm the pumps, the in-line heater or the jets. The risk comes from undissolved crystals, which can lodge in a jet. Dissolve the salt completely in a cup or bowl of warm water before it goes into the bath.
Should the jets be running while Epsom salt is in the water?
The team's best-practice advice is to run your hydro, air or microbubble therapy first and add the dissolved salt for a still soak afterward. Dissolved salts will not harm the jetting system. Keeping them out of the running pumps is simply the gentlest routine for the tub.
Are scented or colored bath salts safe for a jetted tub?
They are not recommended. Dyes and fragrance oils can affect the jet system, and oils are hard to flush out of the pumps and lines. If you use them anyway, use them sparingly, dissolve them fully and rinse the tub thoroughly afterward.
Why do I need to rinse the tub after a salt bath?
Salt residue that dries on chrome can eat at the finish and leave spots, and it may discolor the trim over time. Drain the tub when you finish soaking, rinse it with the hand shower, and wipe the chrome and stainless dry. Pay special attention to jet covers, drain plugs, handles and the faucet.
How do I clean the jets after using bath salts?
Run the vinegar flush. Combine 2 cups of white vinegar with 2 cups of water, fill the tub to 1 inch above the highest jets, add the mixture, run the tub for 10 minutes, then drain. This is the same flush Ella recommends once a month.
Can I use bath salts in a soaking tub without jets?
The rules are much more relaxed in a soaking-only tub with no pumps, because there is no jet system for the water to travel through. It is still a good habit to rinse the tub and wipe the chrome after a salt soak, since dried salt can spot the finish.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket