Support Center / Showers, Panels & Accessories / What are plastic shower units and walls actually made of?
Back to Showers, Panels & Accessories

What are plastic shower units and walls actually made of?

Plastic shower units and walls are usually made of acrylic, of fiberglass, or of the two layered together, and the word plastic most often describes the glossy acrylic surface you see instead of the whole construction. In the Ella's Bubbles line, the acrylic shower pans are an acrylic capped ABS sheet backed with high density foam, the shower stalls and roll-in bases are fiberglass shells finished in AcrylX acrylic, and the wall panels are acrylic. What are acrylic and fiberglass tubs and showers made of? sorts the two materials out across tubs and showers. This page stays with the shower and goes through it part by part.

The Materials Hiding Behind the Word Plastic

Three materials do most of the work in a factory-made shower, and each one has a different job.

  • Acrylic is a solid plastic sheet that is heated and formed into shape. It is the glossy surface you see, touch and stand on.
  • Fiberglass is glass fiber set in resin. It gives a shell its shape and strength, but on its own it is not a bathing surface. It is always finished with something, either a sprayed gel coat or an applied acrylic layer.
  • ABS is the backing layer in the sheet used for Ella's acrylic shower pans. The acrylic cap is the surface, and the ABS underneath gives the sheet its body.

So when a shower is described simply as plastic, it could be an acrylic sheet over a backing, a fiberglass shell with an acrylic finish, or a fiberglass shell with a gel coat finish. The surface may look similar in all three. What sits underneath is what differs, and that is what decides how the unit is supported, where grab bars can be mounted and how it is installed.

Ella Shower Parts and What Each One Is Made of

The table lists the constructions described in Ella's published shower articles. Where those articles do not name a material, the cell says not listed.

Shower partSurface you seeWhat is underneathWhat it means for you
Standard and custom acrylic shower pansAcrylic, as the cap of a vacuum molded acrylic capped ABS sheetABS backing with high density foam bonded to the undersideSits directly on a level subfloor or concrete floor without a mortar bed
Barrier-free roll-in basesAcrylX applied acrylic finishFiberglass shellPre-sloped, self-supporting and pre-leveled, with a textured slip-resistant floor and a beveled entry
One-piece E-series stalls and multi-piece shower kitsAcrylX applied acrylic finishFiberglass with Armorcore reinforced wallsGrab bars and seats can be mounted anywhere on the wall
Legacy ESM series stalls and gel coat multi-piece showersGel coatFiberglassThe older construction, with its own published warranty term
Acrylic wall panels and three-piece wall systemsAcrylic, in white, CNC and digital print finishesnot listedFinished walls that are used as they arrive, with no tile over them
L-shaped filler piecePlasticnot listedCloses a gap beside the base and can be trimmed to fit

What the differences mean: the surface is acrylic on every current Ella shower part, so day-to-day use and cleaning are the same across the line. The layer underneath is what changes. A foam-backed pan is supported by its own reinforcement on a level floor. A fiberglass roll-in base carries its own shape and load. A fiberglass stall with Armorcore walls gives your installer solid backing wherever a grab bar or seat needs to go. Knowing which construction you have tells your contractor how the unit should be set and fastened.

How the Acrylic Shower Pans Are Built

Ella's standard and custom acrylic bases start as an acrylic capped ABS sheet. The sheet is vacuum molded into the shape of the pan, and high density foam is then bonded to the underside of the shell. That foam is the reinforcement. It is what makes the pan rigid enough to be set directly on a level subfloor or concrete floor without a mortar bed, so your contractor is not mixing and screeding a bed before the base goes down. Custom made-to-order pans are reinforced from the bottom the same way as the standard sizes.

The standard sizes are 30 by 60, 32 by 60 and 36 by 60 inches with a left or right drain, and custom rectangular pans run up to 44 inches wide by 80 inches long. The published documents do not give a user weight rating for the pans, so the team at (800) 480-6850 confirms the rating that applies to a specific base. Are Ella acrylic shower pans reinforced, and how much weight do they hold? covers the reinforcement in full.

Stalls and Roll-In Bases: Fiberglass Under an Acrylic Finish

Ella's made-in-the-USA shower stalls, multi-piece shower kits and barrier-free roll-in bases are a different construction. The fiberglass gives the unit its shape and strength, and AcrylX, which Ella's product pages describe as a long lasting applied acrylic finish, is the surface you see and touch. AcrylX is acrylic. It is applied over a fiberglass-reinforced shell instead of being a stand-alone sheet, and Ella's care instructions treat it exactly like any acrylic fixture. On the stalls and kits, Armorcore reinforced walls sit behind the finish on all sides, which matters when a bather's needs change after the shower is installed and a grab bar or seat has to be added.

The older alternative is gel coat. The legacy ESM series one-piece stalls and the low-threshold gel coat multi-piece showers use a gel coat finish over fiberglass. Their published documents print a 3 year limited warranty, while the AcrylX with Armorcore one-piece stalls print a Lifetime Limited Residential Warranty and a 30-Year Commercial Warranty. What is AcrylX and how does it compare to acrylic? explains the finish and the comparison with gel coat.

Walls and Filler Pieces

Ella's shower walls are large acrylic panels. The line includes 98 by 60 inch back walls and 36 to 38 by 96 to 98 inch side walls, along with three-piece acrylic wall systems in white, CNC and digital print finishes, with ADA accessories available. Ella also lists SMC seamless showers among its shower options.

One part is described simply as plastic. The L-shaped filler piece is a plastic accessory, 8 inches wide, that closes a gap between a shower base and an adjoining wall or fixture. It comes with brackets, and because it is plastic it can be trimmed down if it is too large for the space. The current options are listed in Shower Bases, Walls, and Filler Pieces.

What the Materials Mean for Cleaning and for Tile

Because the surface is acrylic, the one rule in every Ella care document is no abrasives. Clean with warm water and liquid detergent or a non-abrasive cleanser made for fiberglass bathroom fixtures, and never use scouring powders, scouring pads or steel wool.

The same finished surface is why these parts are never tiled. Acrylic is a smooth finished surface that does not accept thinset, so tile laid over an acrylic base would not bond reliably and could trap water underneath. Tiling over the pan would also bury the molded slope and threshold that move water to the drain. Ella's custom acrylic pans are described as finished, not tile-ready. What is an acrylic shower, and how does it compare to tile? looks at where tile still fits in a shower design.

Common Questions

Is a plastic shower the same thing as an acrylic shower?
Often it is. Acrylic is a solid plastic sheet, and it is the glossy surface on Ella's shower pans, wall panels and AcrylX finished stalls. The word plastic does not tell you what is underneath, which may be ABS and foam on a pan or fiberglass on a stall or roll-in base.
Are Ella shower stalls made of acrylic or fiberglass?
They are both. Ella's made-in-the-USA shower stalls are fiberglass shells finished in AcrylX, an applied acrylic finish. The fiberglass gives the stall its shape and strength, and the acrylic is the surface you see and touch.
What is the ABS layer in an Ella shower pan?
The standard and custom acrylic pans are vacuum molded from an acrylic capped ABS sheet. The acrylic is the glossy surface you stand on, and the ABS is the backing that gives the sheet its body. High density foam is bonded underneath as the reinforcement.
Does an Ella acrylic shower pan need a mortar bed?
No. The high density foam bonded to the underside makes the pan rigid enough to sit directly on a level subfloor or concrete floor without a mortar bed. Your contractor sets the base on that level surface and connects the drain.
Can I tile over a plastic or acrylic shower base?
No. Acrylic is a smooth finished surface that does not accept thinset, so tile would not bond reliably and could trap water underneath. Ella's acrylic pans are finished and are used as they arrive.
How should I clean an acrylic or AcrylX shower surface?
Use warm water and liquid detergent, or a non-abrasive cleanser made for fiberglass bathroom fixtures. Never use scouring powders, scouring pads or steel wool. The same care applies to AcrylX because it is an acrylic finish.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket