Support Center / Plumbing & Electrical / Can My Installer Reuse the Existing Drain From My Old Jetted Tub?
Back to Plumbing & Electrical

Can My Installer Reuse the Existing Drain From My Old Jetted Tub?

Your installer reuses the house drain connection, not the drain hardware from the old jetted tub. Every new Ella walk-in tub arrives with its own drain assembly, and the tub's drains connect to your house drain through 2 inch fittings, so on many models the assembly adapts to the existing hookup without moving the floor drain itself. Is 40 Amps Enough for a Whirlpool Walk-In Tub With a Dual Drain? describes the dual drain body, and this page covers what stays, what is replaced and what your installer checks once the old tub is out.

What Carries over from the Old Tub and What Does Not

It helps to separate the old tub's own parts from the plumbing that belongs to the house.

  • The old tub's drain hardware does not carry over. The waste and overflow fitted to your jetted tub was made for that tub. Your Ella tub comes with its own drain assembly, already matched to the shell.
  • The house drain usually stays where it is. The new tub's drains tie into it through 2 inch fittings. Many models use a 2 inch drain assembly that can adapt to your existing hookup, so the floor drain itself does not have to move.
  • The tub spout and handles are normally replaced. Ella tubs use their own deck-mount faucet packages. A shower head already on the wall can stay in place above the new tub, as Can I Keep My Existing Shower and Add a Glass Door to the Tub? explains.
  • The old tub's electrical circuit has to be checked, not assumed. The breaker and wire that served the old equipment were sized for that equipment. Can I Reuse My Old Hot Tub Wiring for an Ella Walk-In Tub? lists the checks a licensed electrician makes before anything is plugged in.

How the Drain on an Ella Tub Is Built

Ella walk-in tubs are known for their dual drain design. On the dual drain models, the drain body is a T-type with four 2 inch ports. Your installer can use all four ports, or use two and cap off the unused side. That choice is what makes the tub flexible when it meets plumbing that was laid out for a different tub. The house drain can be approached from either side, and the installer picks the configuration that suits the pipe already in your floor.

Not every model has two drains. The Ella Standard, for example, has one 2 inch gravity floor drain with an overflow and an emergency pull-up chain. Keep your model name handy when you talk with your installer, so the plan is drawn for the drain your tub really has.

The installation video for the Big4One shows this on a real job. It shows two different drain configurations, images of a drain setup before and after the two drain system went in, the dual drains with individual p-traps, and the new connection to the main drain. The customer in that video chose to use two of the four ports and capped off the unused side.

The Door Side Decides Where the Drains Land

The door and the drains are on opposite sides of an Ella walk-in tub. As you face the tub, a right-side door tub has its drains on the left, and a left-side door tub has its drains on the right. If you have read a different description elsewhere, drains opposite the door is the correct one.

This matters for reusing your house drain. Before you order, note which end of the alcove the old jetted tub drains at, then choose the door side that brings the new tub's drains closest to that point. It is the simplest way to keep the tie-in short and avoid rerouting plumbing. Your Ella dealer or the team at (800) 480-6850 can confirm the drain position for your model before your order is placed.

What Your Installer Checks Once the Old Tub Is Out

  1. Reassess the drain, the water supply lines and the electrical connections. This is done after the old tub and fixtures are removed and before the new tub comes into the house. What looked reusable with the old tub in place can look different once the floor is open.
  2. Check the size of the house drain. A 2 inch main drain is recommended for faster draining. If the house drain is sized at one and a half inches, the installer can still connect into it with a T or a Y connection.
  3. Choose the drain configuration. On a dual drain model, the installer decides whether to use all four ports or to use two and cap the unused side, depending on your house plumbing.
  4. Look at the supply side while the wall is open. Easily accessible shutoff valves placed close to the tub are recommended, and three-quarter inch supply lines are strongly recommended for faster filling.
  5. Protect the tub on the way in. End panels, side panels and aprons are removed before the tub is carried into the home to prevent damage.
  6. Level the tub before the final connection. Ella tubs have adjustable leveling legs. Without proper leveling, the door may not function properly and may leak, so the drain tie-in is finished with the tub level and in its final position.

Who Does the Work and Where to Get Help

Ella's Bubbles manufactures the tub and does not install it or send technicians. A local licensed plumber of your choosing removes the old jetted tub and makes the drain connection, and a licensed electrician handles the circuits. Any licensed installer is fine for the job.

The Lifetime Limited Warranty covers parts. Installation, plumbing and electrical connections are not part of that coverage, which is one more reason to have the drain tie-in done by a licensed professional who stands behind their own labor.

Technical support is free for the life of the tub. Your installer can call (800) 480-6850 during the job with any question about the drain tie-in, or you can open a request at ellasbubbles.com/support. Have the model name ready, and a photo of the open floor and the existing drain is a great help.

Video

Watch: Ella's Bubbles: Installation Tips For The Ella Big4One with chapters and a full transcript.

Video

Common Questions

Does a new Ella walk-in tub come with its own drain?
Yes. Every new Ella walk-in tub comes with its own drain assembly, so the drain hardware from your old jetted tub is not reused. The new assembly connects to your house drain through 2 inch fittings.
Will the floor drain have to be moved for the new tub?
Often it will not. Many models use a 2 inch drain assembly that can adapt to your existing hookup without moving the floor drain itself. Your installer confirms this once the old tub and fixtures are out and the drain can be seen.
Can an Ella tub connect to a one and a half inch house drain?
Yes. A 2 inch main drain is recommended for faster draining, but the installer can use a T or a Y connection into a house drain that is sized at one and a half inches.
Do all four ports on the dual drain have to be used?
No. The dual T-type drain has four ports, and your installer can use all four or use two and cap off the unused side. The choice depends on how your house plumbing is laid out.
Which side of an Ella walk-in tub are the drains on?
The drains are on the side opposite the door. As you face the tub, a right-side door tub has its drains on the left, and a left-side door tub has its drains on the right.
Does Ella's Bubbles send someone to connect the drain?
No. Ella does not install tubs or send technicians, so a local licensed plumber makes the drain connection. Technical support is free, and your installer can call (800) 480-6850 with questions during the job.

About this guide. Answers in the Ella's Bubbles Ella's Bubbles Walk-In Tub Support Center are compiled from real conversations with owners, our technicians’ notes and the product documentation, then reviewed by our team. Models and options have evolved over the years, so a detail here may differ slightly from yours. If something looks different on yours, send us your serial number and a specialist will confirm it for your model.

Was this helpful?

Did this solve your question?

If not, open a ticket and our team will pick it up from here.

Open a Support Ticket